background image

EB 2522 EN 

 23

Mounting and start-up

5.2  Quick check

Pressure test

A pressure test of the plant with the regulator 
already installed is only permissible up to the 

nominal pressure of the valve (see Table 1). 

The pressure at the operating diaphragm 

must not exceed the maximum permissible 

pressure. If this cannot be guaranteed, pro-
ceed as follows: unscrew the control line at 
the actuator and seal the open control line.
All plant components must be designed for 
the test pressure.

5.3  Putting the regulator into 

operation

1.  Make sure the control line is correctly 

connected and free of dirt. The cross-sec-

tional area of flow must be open.

2.  Slowly open the shut-off valves on the 

upstream pressure side.

3.  Open all the valves on the consumer side 

(downstream of the regulator). Avoid 
pressure surges.

5.4  Adjust set point

The regulator in the delivered state does not 

have a defined pressure set point. The set 

point spring is released of tension. The set 
point must be adjusted on starting up the 
plant.

Adjusting screw 

(8), SW 27

Fig. 10: 

Set point adjustment (view from 

above)

Adjust the required set point (see Fig. 10) by 

tensioning the set point springs (7) at the set 
point adjuster (8) using a suitable socket 

wrench (width across flats 27).

1.  Remove the cap (12).
2. 

Use a socket wrench (SW 27) to turn the 

screw (8).

Turn clockwise (

) to increase the pres-

sure set point (the upstream pressure in-
creases).

Turn counterclockwise (

) to reduce the 

pressure set point (the upstream pressure 
drops).

Incorrect control due to a set point adjuster 

being turned too far.

If the set point adjuster is turned too far, the 
regulator becomes blocked and closed-loop 
control is no longer possible.
Only screw the set point adjuster up to the 
point where the spring tension can still be 
felt.

3.  Remount the cap (12).

NOTICE

!

Summary of Contents for 2406

































Reviews: