background image

 

13

• 

Ensure the supply connection point; test point and natural gas regulator adjustment screw (for 
Natural gas installation) are accessible for testing and/or adjustment with the hotplate in the 
installed position. 

NG Regulator and pressure test adapter should be provided by installer.

• 

Where a flexible hose assembly is used, ensure it is approved to AS/NZS 1869, Class B. Any hose 
assembly used must be restrained from accidental contact with the flue outlet of an under bench 
oven. 

• 

Prior to connecting the appliance check that the data on the rating plate affixed to the bottom of 
the appliance, correspond to those of the gas mains. 

• 

A duplicate Data Label is supplied to adhere in an accessible area next to the appliance. 

• 

This appliance is suitable for Natural Gas and Universal LPG; ensure that the available gas supply 
matches the Data Label.

• 

Once installed and connected to gas, check there are no leaks using a soapy solution (never a 
flame).

• 

Do not modify this appliance.

10

F I G U R E

mm

This hose assembly shall be suitable for con-
nection to a fixed consumer piping outlet  
located as shown in (fig. 10) 
Hotplates at a point 800 mm to 850 mm above 
the floor and in the region outside the width of 
the appliance to a distance of 250 mm.

Denotes region for flexible hose.

The gas connection is situated at the rear of the appliance, 105mm from the right side and 45mm from 
the rear of the hotplate.
There are two ways to carry out the connection to the main gas line:
a) The hotplate can be connected with rigid pipe as specified in AS5601.
b) The hotplate can be connected with a Flexible Hose, which complies with AS/NZS 1869 (AGA Ap-
proved), 10mm ID, class B or D, no more than 1.2m long and in accordance with AS5601. Ensure that 
the Hose does not contact the hot surfaces of the hotplate, oven, dishwasher or other appliance that 
may be installed underneath or next to the hotplate. 
WARNING: Ensure that the hose assembly is restrained from accidental contact with the flue or flue 
outlet of an under bench oven. The hose should not be subjected to abrasion, kinking or permanent 
deformation and should be able to be inspected along its entire length. 
Unions compatible with the hose fittings must be used and connections tested for gas leaks. The  
supply connection point shall be accessible with the appliance installed. The appliance’s gas inlet 
fitting is a ½” male threaded cylindrical gas type.

Summary of Contents for SCG-4622B























Reviews: