background image

 

14 

OPERATION AND ADJUSTMENT

 

 
 

 

 

       

 

FIGURE 20   

 

 

 

          FIGURE 21 

 

13. Adjusting Glue Pot / Glue Auger 
 

If the glue auger is not perpendicular to the panel face it may be easily adjusted by removing the 
cover from the glue hinge access opening 

(FIGURE 21)

 and using a 3/16” Hex Wrench to loosen 

the adjusting screws 

(FIGURE 22).

 Using the aluminium square provided 

(Figure 20),

 tilt glue 

pot until glue auger is perpendicular to the machine top and retighten screws.  

NOTE:  The auger 

is factory aligned and tested however due to shipping it may have moved slightly and need 
minor alignment, following these procedures.   POWER MUST BE DISCONNECTED AND 
GLUE POT ALLOWED TO COOL BEFORE PERFORMING THIS ADJUSTMENT.  
 
 

 

 

       

 

FIGURE 22   

 

 

 

       FIGURE 23 

 

NOTE:  Hinge Access opening (FIGURE 21) also allows access to hinge pin grease fittings.  
The hinge pin should be lubricated after every 40 hours of use with a high quality high 
temperature grease 
(FIGURE 23). 

Adjustment Screws 

Grease Fittings 

Glue Hinge Access Door 

Summary of Contents for 72GP



















Reviews: