SAFETRACK ECONECT PinBrazing User Manual Download Page 19

Page: 19 / 24

ACCESSORIES AND SPARE PARTS

Heavy Duty Case

Inside fits the following

(not included):

• Grinding Machine

• Grounding Device

• PinBrazing Gun including cable

• Protective Eyewear

• Carrying Harness

• 2 tins (for Brazing pins & Ferrules)
Dimensions:

459x319x160 mm

Weight:

3,4 kg

Part no:

95240

Grinding Machine 18V

• Long-nose type

• Round collet nut reduces risk of damage on workpiece

• Restart function with warning light

• Rubber protection for heat insulation and grip

Technical information:

• Maximum wheel size 38 mm

• Speed (rpm) 25 000

• Incl. 2x 18V Li-Ion battery, 220V charger and case.
Dimensions:

402x82x118 mm

Weight:

2,0 kg (5.61 kg for the cpl. package)

Part no:

593070

Carbide burr Type C

Tungsten carbide,

double diamond cut burr.
Suitable for Steel, Hardened Steel,

Stainless Steel, Cast Iron, Titanium,

Nickel, Copper / Copper Alloys.
Dimensions: 6 mm shank, 12

mm head diameter, 25 mm head

length, 70 mm overall length.

Part no: 8014

Grounding Device 300A

Switchable grounding

magnet complete with

cable and connections.
Length: 2,7m

Weight: 1,22 kg

Part no: 80730

Back Carrying Harness

Carry the Econect unit on your back.

Complete with Holster.
Weight: 3,5 kg

Part no: 93690

Insulation Bag for Econect

Increased capacity in even colder weather.

Part no:

937005

Angle Head Gun

The angle gun makes it

possible to pinbraze on the

web between two close rails

in for example a switch or

crossing, both at the head

and the web of the rail.
Weight: 1,7 kg

Part no: 910151

Grounding Grip

Used for grounding of non-magnetic ma-

terials such as manganese rails, for pipes

or for avoiding to grind the grounding

spot and save some battery capacity.
Weight: 1,7 kg

Part no: 8071

Charger for Econect

Powerful stationary charger for

PinBrazing unit Econect.

36V/230V

Weight: 2 kg

Part no: 8048

Car Charger for Econect

Used for charging the

PinBrazing unit Econect

through the cars 12V

outlet.
Weight: 1 kg

Part no: 80561

Summary of Contents for ECONECT PinBrazing

























Search results

Summary of Contents for ECONECT PinBrazing

Reviews:

Related manuals for ECONECT PinBrazing

Brands by name

Popular brands

SAFETRACK ECONECT PinBrazing, User Manual

Search results

Summary of Contents for ECONECT PinBrazing

Reviews:

Related manuals for ECONECT PinBrazing

Brands by name

Popular brands