SAF-HOLLAND FWAL Series Rebuild/Repair Manual Download Page 18

Page: 18 / 24

XL-FW535 Rev G · 2014-08-11 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, and

logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Rebuild Procedures

Figure 26

Figure 25

8. Springs Installation

8.1 Standard (Non-Air Release)

1. Refer to

Figure 25

for the following three (3) steps:

a. Hook one end of the release handle extension springs

(smaller diameter spring inside the larger diameter
spring) onto the release handle and the other end to
the fifth wheel top plate. Make sure the spring hook
ends face away from the fifth wheel top plate.

b. Connect one end of the release cam extension spring

into the release cam and the other end to the fifth
wheel top plate. Make sure both spring hook ends
face away from the fifth wheel top plate.

c. Install the lock extension spring by hooking one end

to the hole on the lock and the other end to the fifth
wheel top plate. Make sure both spring hook ends
face away from the fifth wheel top plate.

8.2 Air Release

1. Refer to

Figure 26

for the following three (3) steps:

a. Connect the loose end of the release handle extension

spring to the air cylinder pickup. Make sure the spring
hook end faces away from the fifth wheel top plate.

b. Install the release cam extension spring, connecting

the release cam to the top plate. Make sure both
spring hook ends face away from the fifth wheel top plate.

c. Install the lock extension spring, connecting the hole

on the lock to the top plate. Make sure both spring
hook ends face away from the fifth wheel top plate.

RELEASE CAM

EXTENSION

SPRING

RELEASE CAM

EXTENSION

SPRING

RELEASE HANDLE

EXTENSION SPRING

LOCK

EXTENSION

SPRING

LOCK

EXTENSION

SPRING

RELEASE HANDLE EXTENTION SPRINGS

(SMALLER SPRING INSIDE LARGER SPRING)

Summary of Contents for FWAL Series

























Search results

Summary of Contents for FWAL Series

Reviews:

Related manuals for FWAL Series

Brands by name

Popular brands

SAF-HOLLAND FWAL Series, Rebuild/Repair Manual

Search results

Summary of Contents for FWAL Series

Reviews:

Related manuals for FWAL Series

Brands by name

Popular brands