background image

10 — English

OPERATION

 

Set the choke lever to the 

FULL chOKE

 position.

 

Squeeze the throttle trigger fully and pull starter grip and 
rope sharply until engine attempts to run. Do not pull the 
starter grip and rope more than four (4) times.

 

NOTE: 

Keep throttle trigger squeezed fully.

 

Set the choke lever to the 

hALF chOKE 

position.

 

Pull the starter grip and rope until the engine runs. Do not 
pull the starter grip and rope more than six (6) times.

 

NOTE: 

If the engine does not start, return to the 

FULL 

chOKE 

position and repeat the steps that follow.

 

Allow the engine to run for 10 seconds, then set the choke 
lever to the 

RUN

 position. 

To restart a warm engine:

 

Slowly press the primer bulb 10 times.

 

Set the choke lever to the 

RUN

 position. 

 

Squeeze the throttle trigger fully and pull the starter grip 
and rope until the engine runs.

To stop the engine:

  To stop the engine, release the throttle trigger and depress 

the 

STOP

 switch to the stop position “   ”.

IF ASSISTANcE IS REqUIRED FOR ThIS PRODUcT:

Do not return this product to the retail store where it was 
purchased. Please call our Customer Service Department 
for any issues you may have.  

For Help Call: 1-800-860-4050

OPERATING ThE BRUSh cUTTER

See Figure 15.

WARNING:

Engine housing can become hot during operation.  Do 
not rest or place your arm, hand, or any body part against 
the engine housing during operation. Only hold the unit 
as shown in Figure 15 during brush cutter and Figure 17 
for during trimmer operation with all body parts clear of 
engine housing (or as shown in the applicable attachment 
Operator’s Manual). Extended contact with the engine 
housing can result in burns or other injuries.

WARNING:

Always position the unit on the operator’s right side. The 
use of the unit on the operator’s left side will expose the 
user to hot surfaces and can result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with 
the bottom of the engine above waist level.

Hold the brush cutter with your right hand on the rear handle 
and the your left hand on the “J” handle. Keep a firm grip 
with both hands while in operation. Brush cutter should be 
held at a comfortable position with the rear handle about 
hip height. Maintain your grip and balance on both feet. 
Position yourself so that you will not be drawn off balance 
by the kickback reaction of the cutting blade. 
Adjust the shoulder harness to position the brush cutter 
at a comfortable operating position and to assure that the 
shoulder harness will reduce the risk of operator contact 
with the blade.

WARNING:

Always hold the brush cutter away from the body keeping 
clearance between the body and the product. Any contact 
with the housing can result in burns and/or other serious 
personal injury.

BLADE ThRUST

Exercise extreme caution when using the blade with this 
unit. Blade thrust is the reaction that may occur when the 
spinning blade contacts anything it cannot cut. This contact 
may cause the blade to stop for an instant, and suddenly 
“thrust” the unit away from the object that was hit. This re-
action can be violent enough to cause the operator to lose 
control of the unit. Blade thrust can occur without warning 
if the blade snags, stalls, or binds. This is more likely to oc-
cur in areas where it is difficult to see the material being cut. 
For cutting ease and safety, approach the weeds being cut 
with the brush cutter from the right to the left. In the event 
an unexpected object or woody stock is encountered, this 
practice could minimize the blade thrust reaction. 

TRI-ARc

®

 BLADE

The Tri-Arc

®

 blade is suited only for thicker weeds and pulpy 

stalks. When the blade becomes dull, it can be turned over 
to extend the life of the blade. Do not sharpen the Tri-Arc

®

 

blade.

cUTTING TEchNIqUE - BLADE

See Figure 16.

WARNING:

Extreme care must be taken when using blades to ensure 
safe operation. Read the safety information for safe op-
eration using the blade, refer to 

Specific Safety Rules 

for Brush cutter and Blade Use

 earlier in this manual.

 Always hold brush cutter on your right side with both 

hands when operating. Use a firm grip on both handles.

 Maintain your grip and balance on both feet. Position 

yourself so that you will not be drawn off balance by the 
kickback reaction of the cutting blade.

 

 

Summary of Contents for RY28065





















































Reviews: