![background image](http://html1.mh-extra.com/html/ryobi/rsh2845t/rsh2845t_original-instructions-manual_1505504006.webp)
4
| English
■
Turn the outer locking knob clockwise to
lock in place.
NOTE:
Sharpening the blades requires
very light contact with the shaving plate.
Complete any adjustment slowly to avoid
damaging the product. Over adjusting the
plate can cause serious damage to the
product.
RESIDUAL RISK
Even when the product is used as prescribed,
it is still impossible to completely eliminate
certain residual risk factors. The following
hazards may arise in use and the operator
should pay special attention to avoid the
following:
■
Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
■
Inhalation of dust and particles. Wear dust
mask / filter when necessary.
■
Contact with the cutting mechanism. Keep
unprotected body parts away from the
cutting mechanism at all times.
KNOW YOUR PRODUCT
See page 154
1. Handle
2. Overload protection switch
3. On/off
switch
4. Direction
switch
5. Feeding
chute
6. Shaving plate locking knob
7. Shaving plate adjustment screw
8. Collection
box
9. Wheel
10. Power cord
SHREDDING GUIDE
For best results when shredding, follow the
guidelines shown in the table below.
MATERIAL
SHREDDING METHOD
Twigs up to
6 mm diameter.
Feed into the feeding
hopper at a rate which
the product will accept
without overloading.
Branches up
to 45 mm in
diameter.
Clip off all side growth
with secateurs before
feeding into the feeding
hopper.
Bedding plants,
weeds and
shrubby growth.
Knock soil and stones
off the roots to avoid
damage to the blades.
Freshly cut
foliage, hedge,
and kitchen
waste.(I.e.
cabbage
leaves,
vegetable
peelings etc.)
With any material having
a high moisture content,
it is advised to feed in
some drier sticks at
regular intervals to help
push the material trough
the cutting assembly and
prevent it from clogging.
Dry sticks and
twigs
By inserting these at the
end of your shredding
task, this will help to
clean the moisture and
plant sap from the inside
of the product and the
cutting assembly.
■
Do not allow garden waste to accumulate
before shredding as it will begin to compost,
become too damp and clog the cutting
assembly. Dry material will help most
material to clear the ejection chute. Save
some dry sticks until last to help clean the
blade area.
■
Frequently monitor the build up/collection
of shredded material.
■
The exit of the discharge chute must be
clear at all times to prevent blockages.
■
When the collection box is full, turn the
product Off before emptying.
WARNING
Do not put your hands up inside the
shredder’s discharge chute to clear away
shredded material while the product is
switched on or connected to the mains
supply. The blades are sharp. Wear heavy-
duty gloves and exercise extreme caution
when cleaning and clearing blockages.
WARNING
When feeding long woody branches/stems
into the product be careful of whip and
vibrations as they get caught by the cutter.
The operator must wear eye protection
whenever using the product.
Summary of Contents for RSH2845T
