Ryobi RM300E, Manual

Page: 6 / 44

6
Original Instructions
■ Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition.
■ The blade bolts must be tightened to the recommended
torque.
■ Check the brakes before each use and frequently during
use. Adjust and service the brakes as required.
■ The side discharge chute is a spring-loaded guard that
covers the side discharge opening on the cutting deck
and deflects grass clippings and debris away from the
operator. Always ensure that the motor is off and the
blades have stopped moving before inspecting, moving,
cleaning, or performing maintenance on the side
discharge chute.
■ Replace damaged blades and bolts in sets to preserve
balance.
■ Be careful during adjustment of the product to prevent
entrapment of the fingers between moving blades and
fixed parts of the product.
■ The cutting blades continue to rotate for a few seconds
after the motor is turned off. When servicing the blades,
be aware that even though the power source is switched
off, the blades can still be moved. Never place any part
of the body in the blade area until you are sure the
blades have stopped rotating.
■ The blade on the product is sharp. Use extreme caution
and wear heavy-duty gloves when fitting, replacing,
cleaning, or checking bolt security.
■ After each use, clean the product with a soft, dry cloth.
Any part that is damaged should be properly repaired or
replaced by an authorised service centre.
■ Keep the product free of grass, leaves, or other debris
build-up.
■ Do not use water to clean the product. Use an air moving
device, such as a compressor or leaf blower to remove
grass, leaves, or other debris build up.
TYRE MAINTENANCE
The product is equipped with tubeless tyres with the
following dimensions:
■ Front: 33 x 13 x 15 cm
■ Rear: 40 x 16 x 20 cm
When tyres are worn, the traction of the mower decreases,
which increases the chance of having an accident. Replace
the tyres when the depth on the tread is 4 mm or less, or
any time there is damage to the tyre. Always use original
replacement tyres. Using improper tyres on the product
could cause loss of control, which could cause serious
personal injury.
Have the tyres replaced only by an authorised service
centre.
TYRE AIR PRESSURE
Check the air pressure in all four tyres before each use.
Improper air pressure affects handling, steering response,
traction, tyre life, level cutting, and operator comfort. Make
sure that tyres are inflated to the recommended air pressure
of 1.4 bar (140 kPa).
Tyre air pressure should only be measured or adjusted
when tyres are cold.
TYRE REPAIR
If a leak or flat tyre occurs due to a puncture, the tyre may
be repaired using a plug-type patch. If the damage is from
a cut, or if the puncture cannot be repaired using a plug,
replace the tyre.
BRAKE ADJUSTMENT
See page 22.
If the mower travels farther before stopping when stepping
on the brake pedal, the brakes need adjusting.
After final adjustment, test the brakes by driving the mower
at normal speed on flat ground to be sure that the mower
stops quickly when brake pedal is stepped on.
CLEARING BLOCKAGES
■ Turn off the product, engage the parking brake,
and remove the start key. Set the cutting deck to the
maximum height. Make sure that all moving parts have
come to a complete stop.
■ Always wear heavy-duty gloves when checking or
clearing a blockage. The blades are sharp and the
blockage itself could be a sharp object.
■ Check and carefully clear the side discharge chute for
blockages.
■ Carefully remove any found blockages. Remember that
the blade may move during cleaning.
KNOW YOUR PRODUCT
See page 12.
1. Blade engage knob
The blade engage knob activates or stops the cutting
blades.
● Pull up the blade engage knob to activate the blades.
● Press the blade engage knob to stop the blades.
NOTE: The blades should stop within 5 seconds. If the
blades do not stop, contact an authorised service centre.
2. Headlight button
The headlight button turns the headlights ON and OFF.
3. Power switch
The power switch turns the product ON and OFF. The
start key must be inserted before the switch can be
operated. When the key is in the accessory position,
the power switch is also used to power optional
manufacturer-approved mower accessories.
4. Reverse mode button
The reverse mode button turns on the blades when
manoeuvring in the reverse direction.
NOTE: The blades do not turn on during reverse
operation if the reverse mode button is not pressed and
the blade engage knob is not pulled up.
5. Battery level indicator / hour meter
The battery level indicator shows the amount of battery
charge remaining. The hour meter tracks the total
number of hours the product has been used (key in on
position) for maintenance purposes.
6. Seat (with safety interlock system)
The seat has an interlock system that stops the blades
if the operator leaves the mower while the blades are
running.
Test the system before each use to ensure that it is
working correctly.
1. Press the blade engage knob to stop the blades.
2. Insert the start key, and turn it to the ON position.
3. Pull up the blade engage knob to activate the blades.
4. Briefly stand up but do not get off the mower.
The blades should stop within 5 seconds. If the blades