![background image](http://html1.mh-extra.com/html/ryobi/rcs18x/rcs18x_manual_1506567004.webp)
the lower guard into the open position.
If the saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade or any
other part, in all angles and depths of cut.
■
Check the operation of the lower guard spring. If
the guard and the spring are not operating properly,
they must be serviced before use.
Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
■
Lower guard may be retracted manually only for
special cuts such as “plunge cuts” and “compound
cuts”. Raise lower guard by retracting handle
and
as soon as blade enters the material, the lower
guard must be released.
For all other sawing, the
lower guard should operate automatically.
■
Always observe that the lower guard is covering the
blade before placing saw down on bench or floor.
An unprotected, coasting blade will cause the saw to
walk backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop after
switch is released.
ADDITIONAL SAFETY WARNINGS
■
Do not use any abrasive wheels.
■
Use only blade diameter(s) in accordance with the
markings.
■
Identify the correct saw blade to be used for the material
to be cut.
■
Use only saw blades that are marked with a speed
equal or higher than the speed marked on the tool.
■
Use only saw blades recommended by the
manufacturer, which conform to EN 847-1, if intended
for wood and analogous materials.
■
Wear a dust mask.
■
Clamp workpiece with a clamping device.
Unclamped workpieces can cause severe injury and
damage.
■
Injuries may be caused or aggravated by prolonged use
of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
■
The product will restart automatically if stalled. Switch
off the product immediately if it stalls. Do not switch on
the product again while it is still stalled, as doing so
could trigger a sudden recoil with a high reactive force.
Determine why the product stalled and rectify this,
paying heed to the safety instructions.
■
Ambient temperature range for tool during operation is
between 0°C and 40°C.
■
Ambient temperature range for tool storage is between
0°C and 40°C.
■
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0°C and 40°C.
■
Ambient temperature range for battery storage is
between 0°C and 20°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
KNOW YOUR PRODUCT
See page 82.
1. Hex key
2. Depth adjustment lock lever
3. Dust port
4. Spindle lock button
5. Handle, insulated gripping surface
6. Switch trigger
7. Lock-off button
8. Front handle, insulated gripping surface
9. Bevel adjustment knob
10. Edge guide knob
11. Battery port
12. Lower guard
13. Inner flange
14. Outer flange
15. Blade screw
16. Edge guide fence
17. Blade
18. Operator’s manual
19. Battery pack
20. Charger
MAINTENANCE
■
The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product from the power
supply will prevent accidental starting that could cause
serious injury.
■
When servicing, use only original manufacturer’s
replacement parts, accessories and attachments.
Use of any other parts may create a hazard or cause
product damage.
4
Original Instructions
Summary of Contents for RCS18X
