background image

5

ENGLISH

 SERVICE

Ser vicing requires extreme care and knowledge 
and should be performed only by a qualified service 
technician. For service we suggest you return the product 
to your nearest AUTHORISED SERVICE CENTER for 
repair. When servicing, use only identical replacement 
parts.

WARNING:

To avoid serious personal injury, do not attempt 
to use this product until you read thoroughly and 
understand completely the operator’s manual. 
If you do not understand the warnings and 
instructions in the operator’s manual, do not 
use this product. Call Ryobi customer service for 
assistance.

WARNING:

The operation of any power tool can result in 
foreign objects being thrown into your eyes, 
which can result in severe eye damage. Before 
beginning power tool operation, always wear 
safety goggles or safety glasses with side 
shields and, when needed, a full face shield. We 
recommend Wide Vision Safety Mask for use 
over eyeglasses or standard safety glasses with 
side shields. Always use eye protection which is 
marked to comply with standards.

SAVE THESE  INSTRUCTIONS

INTRODUCTION

This product has many features for making its use 
more pleasant and enjoyable. Safety, performance, and 
dependability have been given top priority in the design 
of this product making it easy to maintain and operate.

 DESCRIPTION OF FIGURES

RBC430SES
Figure 1

1. Shoulder strap
2. Tri-Arc

®

 blade

3. Drive shaft
4. Coupler
5. Strap hanger
6. Ignition switch
7. Trigger lock
8. Rear handle
9. Primer bulb
10. Fuel cap
11. Recoil starter
12. Throttle trigger
13. Latch

14. Front handle
15. Wing knob
16. Blade deflector
17. Choke lever
18. Grass deflector
19. Cutting line
20. Reel-Easy™ line trimmer head
21. Pro Cut II™ line trimmer head
      

Figure 2

22. Lower boom
23. Lock
24. Guide recess
25. Power head (upper) shaft
26. Position hole

Figure 3

27. Hole on the attachment hanger to fit lock button of 

lower booms

28. Attachment hanger
       

Figure 4

29. Screw
30. Clamp
31. Screw
       

Figure 5

32. Gear case assembly
33. Holding pin tool
34. Mounting plate
35. Combination wrench
36. Reel-Easy™ line trimmer head
37. Bolt

Figure 7

38. Oil cap / dipstick
39. Level indicator
40. Oil fill hole
41. Funnel
       

Figure 10

42. Trimmer line cut-off blade
       

Figure 13

43. Start position
44. Run position
     

Figure 15

45. Tri-Arc

®

 blade protector

Figure 16

46. Idle speed screw

Figure 17

13. Latch 
47. Filter screen
48. Air filter cover

RBC430SES/SBS manual(TTIA).indd   Sec2:5

RBC430SES/SBS manual(TTIA).indd   Sec2:5

09-9-23    5:25

09-9-23    5:25

Summary of Contents for RBC430SBS


















Reviews: