background image

3

PRodUct sPecIfIcAtIons

Rated motor power

1500 W

Rated current

6 A

Air outlets

2 pcs, 6.35mm (1/4”) 

Nitto-style quick 

connector (coupler)

Quick connector fitting size

6.35 mm (1/4")

Weight

30.6 kg

Input

220 - 240 V AC, 50 Hz

Power cord length

2.0 m

Air tank capacity

50 L

Free air delivery

120 L/min (4.2 cfm)

Maximum air delivery

190 L/min (6.7 cfm)  

at 0 bar tank pressure

Maximum air pressure

8 bar (115 psi)

Working pressure range

6 - 8 bar (87 - 115 psi)

Pressure gauge

2 pcs, 50.8 mm (2 in.) 

diameter

Maximum rotational shaft 

speed

2,850 rpm

Short-circuit rating  

3 kA

Operating temperature

0 - 45°C

Measured sound pressure 

level (the reference 

number of the noise test 

code: EN ISO 2151:2008)

LpA=70.5 dB(A), 

KpA=2 dB

Measured sound power 

level (the reference 

number of the noise test 

code: EN ISO 2151:2008)

LwA=90.5 dB(A), 

KwA=2 dB

Intended Use

This compressor is designed to supply pressurised air 

only. It must not be used to compress any other gas. It is 

designed to operate air powered tools. The compressor 

should be operated under cover or protected from rain.

AssemBLy

UnPAckIng

This product requires assembly. Carefully remove the 

product and any accessories from the box.

 

 wARnIng

Do not use this product if any parts on the packing 

list are already assembled to your product when you 

unpack it. Parts on this list are not assembled to the 

product by the manufacturer and require customer 

installation. Use of a product that may have been 

improperly assembled could result in serious personal 

injury.
Inspect the product carefully to make sure no breakage 

or damage occurred during shipping.
Do not discard the packing material until you have 

carefully inspected and satisfactorily operated the 

product.

 

 wARnIng

If any parts are damaged or missing do not operate this 

product until the parts are replaced. Use of this product 

with damaged or missing parts could result in serious 

personal injury.

 

 wARnIng

Do not attempt to modify this product or create 

accessories not recommended for use with this 

product. Any such alteration or modification is misuse 

and  could  result  in  a  hazardous  condition  leading  to 

possible serious personal injury.

 

 wARnIng

Do not connect to power supply until assembly is 

complete. Failure to comply could result in accidental 

starting and possible serious personal injury.

Packing list

 

Air compressor

 

Front handle

 

Bottle of oil

 

Air filter

 

Wheel x 2

 

Rubber foot x 2

 

Bolt x 6

 

Nut x 4

 

Flat washer x 8

 

Wheel axle cover x 2

 

Axle bolt x 2

 

Operator's manual

InstALLIng fRont HAndLe

See figure 3.

1.  Insert both ends of the front handle in handle slots.

2.  Secure both ends with 2 hex bolts each using a hex 

Summary of Contents for Airwave RA-C2550-G




















Reviews: