background image

iNstALLAtiON AND sEtuP

RUSTIBUS®

 X400

 

AiR

before you begin.

Step 1:  VERIFY THE COMPLETENESS OF YOUR RUSTIBUS® MACHINE.

• 

Check that all components are attached properly and in a proper / safe working order. 

  (Check that there are no loose wires, guards or parts on the machine)

Step 2:   ASSOCIATED EQUIPMENT.

• 

Ensure that you have available required Air Pressure & volume. 

   (2,4 m³/min (85 CFM ) / 7-8 bar (101-116psi)) 

• 

Ensure that you have available Air tool oil to fill the Lubricator to the required level.

Step 3:  BEFORE COMMENCING THE OPERATION.

 Locate the section to be cleaned / de-scaled and determine if the area needs to be cleaned. Excessive

   grease, dirt and other hazardous material should be cleaned from the surface area before 

   operation of the 

Rustibus®

 machine.

• 

Check the site to ensure the air motor of the machine/tool will be adequately ventilated and that

   there is no external heat input (e.g. couplings).  The cooling air may not exceed 60

°

C

• Check that the air motor of the machine/tool is not damaged. And that the machine /tool itself is 

   not damaged in anyway that may effect its EX/ATEX compliance

• Confirm the correct air pressure before connecting hose supply.

• Check oil level container and fill with air tool oil as required (Only fill to 75%)

•        The Chain drum is rotating at high RPM, show outmost care when connecting Air hose and when 

    operating machine.

 ALWAYS THINK SAFETY FIRST!

• Connect your machine to its power source.

• Make sure the air hose is properly connected and safely located for your operation. Apply safety wire

  on hose.

• 

ALWAYS

 lift up machine (push down the handle) in order for the chain drum to rotate freely when 

   starting the machine.

• Start and Stop the machine and check that rotation is correct according to marking on machine.

Step 4: OPERATION OF RUSTIBUS® MACHINE.

• For the best results from your

 Rustibus®

 machine you should run the machine forward and backward

  over the area until appropriate result is achieved 

• Do not run the machine over sharp edges, but along them. Your machine will last longer if operated 

   with care.

• 

Operate the machine for approximately 2 hours at the maximum desired load. Measure the surface 

   temperatures of the motor casting opposite the ports / or above the main port. Re Check with

   Pre-Start checks.

Genuine Rustibus® parts only!

Machine may vary from pictures

Summary of Contents for 040-X3000
































Reviews: