Runco LightStyle LS-12d, Installation & Operation Manual

Page: 73 / 152

Operation
LightStyle™ LS-12d Installation/Operation Manual 57
PRE
L
IMINAR
Y
4.1
Using the On-Screen
Menus To display the Main Menu, press the MENU button on the remote control or Dimension
Digital Controller front panel (Figure 2-5).
To select a menu item, use the and buttons on the remote control or Dimension
Digital Controller front panel to highlight it. Then, to confirm your selection, press ENTER
on the remote control or Dimension Digital Controller front panel.
The LS-12d OSD menus are arranged hierarchically, as shown in Figure 4-1. Some menu
options apply only to certain input signal types. For example, Phase and Tracking can only
be adjusted for RGB, Component video or SCART signals.
Figure 4-1. L S -12d O S D Menu S tructure
4. Operation
Input S ource
Composite 1 HDMI 1
Composite 2 HDMI 2
Composite 3 HDMI 3
Component HDMI 4
HD 1 HDMI 5
HD 2 HDMI 6
SCART HDMI 7
DisplayPort HDMI 8
A s pect Ratio
16:9
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
S creen
S creen 1 / Screen 2
Picture
Brightness
Contrast
Color
Tint
Sharpness
Noise Filter
Input Po s ition
Left/Right
Up/Down
Width
Height
Overscan
Overscan Mode
(Zoom/Crop)
Phase
(RGB/Component/SCART signals only)
Tracking
(RGB/Component/SCART signals only)
Memory
Pre
s et s
Recall ISF Night or ISF Day
Recall/Save Custom 1 or Custom 2
Reset Custom 1 and Custom 2 to Factory
Default
3D
Proce
ss ing
3D Mode
(
Auto , Off, Side-by-Side, Top-and-Bottom or
Frame Packing)
Reverse Eyes
(On/
Off )
S leep Timer
Off , 30 Minutes, 60 Minutes, 90 Minutes, 2
Hours or 4 Hours
Information
Signal
System
Network
Field Service
Manufacturing
Calibration
Display Color -
Common Settings
Gain
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Offset
Gamma
Mode
(
S imple / Advanced)
Simple
(1.8, 2.0,
2.2 , 2.35, 2.5)
Advanced
(
0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Color Temp Simple (5500K, 6500K, 7500K or 9300K)
Color Gamut*
Auto , REC709, SMPTE-C, EBU, Native or
PCE
PCE*
Red x, y / Green x, y / Blue x, y / White x, y
Yellow x, y / Cyan x, y / Magenta x, y
Display Color -
Projector Settings
Lamp Power (230W or 260W )
ConstantContrast* On / Off
Input Image
Brightness
-50, -49 ... 0 ... 49, 50
Contrast
Color
Tint
Sharpness
Input Color
Gain
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
Offset
Chroma Delay
0 , 1, 2 ... 7
(Composite inputs only)
Noise Filter 0 , 1, 2 ... 63
Save ISF Night
Back / Confirm
Save ISF Day
Copy/Paste
Memory Preset
Copy Settings
Paste Settings
Aspect Ratio
Copy Settings
Paste Settings
Output Shift
Left/Right
-50, -49 ... 0 ... 49, 50
Up/Down
Width
-50, -49, 48 ... 0
Height
Screen Masking
0 , 1, 2 ... 100
(Top / Bottom / Left / Right /
Test Pattern Enable)
Image Alignment
Corner Alignment
Top Left / Top Right / Bottom Left /
Bottom Right / Test Pattern Enable
Midpoint Alignment
Center / Top Middle / Left Middle /
Right Middle / Bottom Middle /
Test Pattern Enable
Adjustment Mode Both , Primary or Secondary
Splash Configure
Owner Name
ISF Calibrated
ISF Other
Splash Timer 5, 6, 7 ... 15 ... 59, 60
Splash Enable On/Off
OSD Position Hor. / Ver. 0 , 1, 2 ... 100
Note: Default settings appear in bold type . Settings marked with an asterisk (*) apply to 2D content only.