background image

 

Tumbler MKR 600 

and indication must remain on the display. - Now close the lid 
fully. - When reaching the 

“Closed”

 end position the lid and in-

dication must remain on the display. If the lid or indication on 
the display do not remain, the machine must be shut down 
immediately! Error messages of the control system must be 
heeded! 

 

!!! To shut down the machine the main switch must be turned to 

“0”

 - 

OFF" and the power plug pulled from the outlet! The machine must be 
secured against further use! 
 
!!! The supervisor must arrange for the repair of the non-functional 
safety device by a Rühle service technician. Until the corresponding 
parts have been repaired, the supervisor must ensure that the ma-
chine or parts of the machine are under no circumstances put into op-
eration! 
 
!!! The cleaning personnel must observe the work procedures from the 

“Cleaning”

 work instructions prepared by the supervisor. 

 
!!! The maintenance personnel may only carry out work specified as 

“Regular care”

, unless any other authorisation has been issued in 

writing by the manufacturer of the machine. The maintenance per-
sonnel must observe the work procedures from the 

“Maintenance”

 

work instructions prepared by the supervisor. 
The power plug must be disconnected for maintenance work! 
 
!!! The machine may not be modified. 
 
!!! Only Rühle spare parts and accessories may be used. 
 
!!! The operating instructions as well as all other technical documents 
included must be supplied completely when reselling the machine. 
 

Summary of Contents for MKR 600



















Reviews: