background image

 

 

 

- page 13 of  13 

– 

Inst ruct ion and operat ing manual CVS  
SKL1200 direct  driven                                                                                                                 

(for-030/031013)

    

 

 

Actions 
COMPRESSOR:

  

O --  Drain oil 

 

O --  Change oil filter  
O --  Check potential leakage machine  
O --    top up oil  
O --  Check oil hose for potential cracks/damages 

CLEAN COMPRESSOR: 

O --  Check rotors for damages or greasiness  
O --  Flush compressor tw ice w ith 1/4L degreaser 
O --  Check rubber compensator for cracks replace if necessary  
O --  Check aluminium pipes and silencers for cracks and leakage     
O --  Check the indicator

’s piping for cracks and leakage  

 

AIRFILTER: 

O --  Take air filter lid off  
O --  

Check the lid’s latches  

O --  Check if the insulation material is secured in suction part 

if this isn’t the case repair and finish w ith sealant  

O --  Check functioning of air filter indicator  
O --  Clear intake-side of degreaser residue  
O --  Place a new  air filter element  

ENCLOSURE: 

O --  Check the insulation material in the enclosure for damages 

 

        (cover, back panel, floor panel) if necessary repair and finish w ith sealant  
O --  Check if the fan louvers are open  
O --  Check if the discharge silencer is clean (flow )  
O --  Check the frame and brackets for potential cracks  
O --  Check if the bolts of the brackets are secured  
O --  Check the seal w ashers of the Storz coupling for cracks and leakage 
O --  

Check the functioning of the cover’s latches  

O --  Tighten the bolts of the mounting brackets  

TRANSMISSION: 

O --  Check the PTO-shaft for leew ay in the cross journals  
O --  Lubricate the PTO-shaft w ith EP grease (red) 
O --  Tighten the bolts of the PTO-shaft flanges  

TESTING: 

O --  Operation test run of machine  
O --  Check density of discharge sides 
O --  Check pressure valve for 2.5 bar  
O --  Check functioning of indicators 
O --  Check the engine for unusual sounds  
O --  Clean the w indow pane  

 

Firma 

  

Date maintenance  

 

Name mechanic 

  

Compressor 

 

Address 

  

Serial number  

 

 

  

Installation-no. 

PO………….. 

Truck 

  

Year manufactured 

 

Truck nr. 

  

Licence plate no.  : 

 

 Chassis:

 

No. KM driven: 

 

Maintenance checklist 

Summary of Contents for SKL1200














Reviews: