background image

 

 

 

- page 11 of  13 

– 

Inst ruct ion and operat ing manual CVS  
SKL1200 direct  driven                                                                                                                 

(for-030/031013)

    

 

5.3 

MONTHLY INSPECTION 

 

 
 

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *  

 

ONLY CARRY OUT WHEN INSTALLATION IS COOL AND AT A STANDSTILL 

 

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

 

 

This  check  may  only  be  carried  out  by  skilled  mechanics.  Observe  the  safety  very 
carefully, the enclosure must be removed and rotating parts will be accessible.  

 
A: 

Lubricate cross journals of the PTO-shaft (after approx. 40 operating hours)  

 

 

B: 

Lubricate latches and padlock and check their functioning.  

 
C: 

Preserve the compressor w hen it has been at a standstill for a longer period of time.   

 

(lubricate the compressor’s rotor w ith oil to prevent corrosion) 

 

To  carry  out  the  follow ing  inspections  it  is  necessary  to  start  the  installation 
w ithout enclosure. Please note the dangers that can occur as a result of access to: 

 

- hot parts as compressor and silencer (150 ° C) 

 

- rotating parts such as the transmission and the fan 

 

- high sound levels (>  85 dB) 

 

HEARING PROTECTION OBLIGATED!! 
 
DURING INSPECTION NO ONE IS ALLOWED UNDERNEATH THE VEHICLE!! 

 
D: 

Check the functioning of the safety valve. 
Air pressure measured at the discharge flange of the compressor may not exceed a 
maximum gauge pressure of 2.5. 

 

Potential pressure loss betw een compressor and silo tank of 0.2 up to 0.3 bar  

 
E: 

Check  flanges/packing,  rubber  compensators  etc.  in  the  enclosure  for  air  leakages 
to avoid loosening of the insulation material and overheating. 

 
F: 

Check the functioning of the fan. 

 
 
 
 
           
 

 

 

 

 

Summary of Contents for SKL1200














Reviews: