Rt IDLV-4000P-30x, User Manual

Page: 17 / 38

En
13
When exiting the ‘Filter List’ sub-menu, a new menu will be shown ‘Confirm
changed?’ Press the <ENTER>-key to validate all programs just be selected to
be filtered away or press the <EXIT>-key to discard the settings.
After a few seconds, the filtered TS will be generated and delivered to the speci -
fied destination(s).
Ethernet
The menu is shown only when the TS/IP streaming is installed and the board is
set to “IP Out”.
The TS/IP Ethernet connector could also be configured as the output of the trans -
port stream over IP. The parameters listed below must be set to appropriate
values for the network that the transport stream over IP is broadcasted.
Stream IP Addr:
Enter the IP address for streaming IP output of the unit.
Stream Netmask:
Enter the network sub mask for the subnet to which the unit is
connected for IP streaming traffic.
Stream Gateway: Set the gateway for the network to which the unit is connected
for IP streaming traffic.
Stream Mac Address: Factory-set MAC addresses are guaranteed to be unique.
Therefore, you cannot configure the address.
Gateway Mac address: Set the MAC address of your gateway. you can leave
it as ff:ff:ff:ff:ff:ff
Protocol: Select the protocol for multicast: UDP or RTP.
TS Pkts per UDP: Set the number of the TS packages encapsulated in one UDP
package. The valid range goes from 1 to 7.
Time to Live: Set the number of the routers over which the TS over IP can be
transmitted. The valid range goes from 1 to 255.
Type of Service: Select the type of service. There are: Normal, Min Monetary
Cost, Max Reliability, Max Throughput or Min Delay optional.
Source: Select the source of the transport stream over IP streaming output.
There are 4 type of source optional: ASI Input, CI De-encrypted, TUNER, Mux TS
(note the Mux TS is showed only when the Mux/Filter function block is enabled
and turned on. The Mux TS indicates not only the after-multiplexed TS when Mux
is enabled, but also the after-filtered TS when the filter is enabled.)
After the operation, the selected transport stream will be delivered to the TS / IP
function block for further operation.
Mode: Select the mode of IP stream, you can select DVB or IPTV.
DVB mode:
The transport stream which comes from the ‘source’ selected in the
previous step will be packed into IP Stream directly. The IP stream will carry all
programs, and this IP stream will be delivered to specified Multicast or Unicast
IP address.
IPTV mode: The transport stream which comes from the ‘source’ selected in the
previous step will be de-Muxed to several single programs, and each program is
packed into one IP stream. Each IP stream is then being delivered to specified
Multicast or Unicast IP address. You can configure up to 32 IPTV channels.
Multicast Setup: Use the <ENTER>-key to enter sub-menu. The sub-menu is
different according to different ‘mode’ selected in previous step.
DVB mode
Multicast IP: Enter the IP address of the IP stream for the transport stream over
IP output. You can configure the IP stream output mode in Multicast or Unicast.
Multicast could be established by setting Multicast IP address in the range be-
tween 239.255.255.255 and 224.0.0.0.
Unicast could be established with the same settings of Multicast, but there is a
difference. The IP address should NOT be set in the range between 224.0.0.0
and 239.255.255.255. Although the display is ‘Multicast IP’ on the first row, the
stream itself is Unicast. The IP address of the receiving device (may be PC with
VLC) needed to be set to the same unicast address as the one on IDLV-4000P.
Please don’t use DHCP to get a dynamic IP address for the receiving device.
Multicast UDP Port: Enter the UDP port number of the TS over IP stream out-
put.