RVV Gen II KO Service and Parts Manual
28
SECTION 3: Vender Programming
•
C3 - POS Message Disable
This option is used to turn off the display of the point-
of-sales message.
If X = 0, the point-of-sales greeting will appear as
normal.
If X = 1, the point-of-sales greeting will not appear on
the display.
•
C4 - Display Open Door Totals
This option is used to turn on the display of the total
machine sales and total machine cash values in the
open-door mode.
If X = 0, only summary error codes will be displayed
when the door is open.
If X = 1, sales and cash totals will be displayed and
“Errors” or “None” will replace the error codes when
the door is open.
•
C5 - Door Switch Reset MIS
This option is used to allow the door switch to reset all
resettable MIS (resettable cash and sales counts, etc.).
If X = 0, all resettable MIS registers are reset only
when the “CF” command is received from the hand
held device (HHC).
If X = 1, all resettable MIS registers are reset when
the door switch is sensed as open and at least one
of the resettable MIS registers has been read (i.e.,
individual cash and sales counts).
•
C7 - Save Credit
This option is used to determine how long credit
should remain on the display and available to the
customer. If the feature is turned off, a five-minute
timer is restarted each time credit is added to the
machine, or any valid consumer action occurs. After
the timer expires the credit is erased. If the feature
is turned on, credit is left available to the customer
regardless of when it was deposited.
If X = 0, the five-minute timer is used.
If X = 1, credit is left on the display for use
indefinitely.
•
C8 - Force Vend
This option prevents the machine from becoming a
change maker. When this mode is enabled, escrow
of coins is allowed until any of the following
three events occurs: 1. Any bill is taken into the
bill acceptor; 2. Any “cash box” coin is inserted
into the changer; or 3. The maximum vend price
is reached. Once any of these conditions are met,
any accumulated credit must be used toward a vend
attempt, and coins will not be dispensed for credit in
response to an escrow request. If a sold out selection,
or if a valid selection that becomes sold out, is made
this option will be over-ridden and an escrow will be
honored.
If X = 0, forced vend attempt is disabled.
If X = 1, forced vend attempt is enabled.
Note that force vend has no effect on the card reader;
once a card is inserted it can always be returned to
the customer via the escrow lever on the changer or
return button on the card reader.
•
C9 - Multi-Vend
This option will allow multiple purchases without
re-entering coins. If enabled, instead of immediately
returning the change after a vend, the credit will
remain on the display to be used for another selection.
An escrow request will be honored at any time. This
option will take precedence over the force vend option
after the first vend has been completed.
If X = 0, multi-vend is disabled.
If X = 1, multi-vend is enabled.
•
C10 - Bill Escrow Inhibit
This option will inhibit escrowing of bills. If
disabled, and the current bill value inserted takes
the accumulated credit over the maximum price, the
bill will be held in the escrow position. If the rule is
enabled, bills will always go to the cash box.
If X = 0, Bill Escrow is allowed.
If X = 1, Bill Escrow is inhibited (bill sent to cashbox).
•
C16 - Rdr Lvl Enb
This option allows cashless devices (such as card
readers) to use MDB Level 2 communication protocol.
When enabled, card revaluing is supported.
If X = 0, MDB Level 2 is disabled for cashless
devices (no card revaluing).
If X = 1, MDB Level 2 is enabled for cashless devices
(i.e., card revaluing is enabled).
