background image

3

VARIETY STEAMER (VS-250)

P/N 1010998 Rev. C 11/12

Service/Technical Assistance

If you experience any problems with the installation 

or operation of your unit, contact your local Roundup 

Authorized Service Agency.  They can be found in the 

service agency directory packaged with the equipment.

Fill in the information below and have it handy when 

calling your Authorized Service Agency for assistance.  

The serial number is on the specification plate located 

on the rear of the unit.

Purchased From:

Date of Purchase:

Model No.:

Serial No.:

Mfg. No.:

Refer to the service agency directory and fill in the 

information below:

Authorized Service Agency

Name:

Phone No.:

Address:

Use only genuine Roundup replacement parts in this 

unit.  Use of replacement parts other than those sup-

plied by the manufacturer will void the warranty. Your 

Authorized Service Agency has been factory trained 

and has a complete supply of parts for this unit.

You may also contact the factory at 

1-877-392-7854 

or

  630-784-1000 

if you have trouble locating an 

Authorized Service Agency.

OWNER INFORMATION (continued)

IMPORTANT

A.J. Antunes & Co. reserves the right to change specifications and product design 

without notice.  Such revisions do NOT entitle the buyer to corresponding changes, 

improvements, additions, or replacements for previously purchased equipment.

Summary of Contents for 9100260

























Reviews: