background image

9

VARIETY STEAMER (VS-250)

P/N 1010998 Rev. C 11/12

OPERATION

Figure 3. Operator Controls

TIMED CYCLE

The desired timed steaming cycle (up to 99 minutes 

and 59 seconds) is selected by pressing and releas-

ing any of the four menu buttons (Figure 3).  The main 

Control Board applies power to the solenoid at regular 

intervals for the duration of the displayed cycle time.  

The display counts down to zero when the cycle is 

complete, then reverts back to the original programmed 

cycle time and the unit is ready for the next cycle.

IMPORTANT:  Your steamer is factory programmed 

for the following (on each of the 4 menu channels):

 •  Total Cycle Time = 10 seconds [00:10]

 

(Range:  1 second to 99 minutes and 59 seconds)

 •  Shot Interval Rate (RATE) = 5 seconds [00:05]

 

(Range: 1 second to 5 minutes and 59 seconds)

 •  Steam Shot Time (SHOT) = 

0.70 second 

[00:70]

 

(Range: 0.10 second to 2.50 seconds)

This converts approximately 3/4 oz. (25 milliliters) 

of water to steam every 5 seconds for a 10 second 

steaming cycle.  To change any of these settings refer 

to the Programming section of this manual

.

Operator Controls

POWER SWITCH

When the Power Switch is on, the Control Board 

is activated.  If the Generator temperature is below 

the factory preset setpoint, power is applied to the 

Generator until the setpoint temperature is reached.  

The Generator is constantly monitored and power is 

regulated to maintain the temperature setpoint.

MENU BUTTONS

When any menu button is pressed and released, 

power is supplied to the solenoid, the solenoid oper-

ates, and water sprays onto the heated Generator sur-

face.  The water flashes immediately into live steam to 

heat the product.

One of two operational modes can be used: Single 

Shot or Timed Cycle

SINGLE SHOT

The 

SINGLE SHOT

 button (Figure 3) is pressed and 

released to initiate a single shot.  The Control Board 

applies power to the solenoid and a single shot of 

steam occurs.

Display Window

Program  

Button

Single Shot  

Button

Up and Down 

Arrow Buttons

Power Switch

Menu Channel Buttons

Lock Lever

Menu Channel Indicator Lights

Summary of Contents for 9100260

























Reviews: