background image

ROTORCOMP VERDICHTER

Operating Manual - 

EVO

®

 Line

7.2

[en] 07/2020

7.2 Oil level

An important factor for the operating safety of the 

system is the oil level in the oil reservoir. 

The oil level check must be carried out before 

commissioning the screw compressor module and 

then repeated every 100 operating hours.

Warning:

Rotating, pressurized and hot components, 

DANGER OF INJURY!

7.2.1 Oil level check via oil filler opening

Warning:

– The unit parts, oil and oil filler plug may be over 

80°C/176°F; danger of burns! 

Wear personal safety equipment!

– With hot oil, the oil level can be higher than with 

cold oil shortly after discharging.

As a result, oil may escape when the oil filler 

plug is opened at the maximum oil level. In this 

case, close the oil filler plug again immediately 

and carefully remove the oil which has 

escaped.

Switch off the system and secure it against 

unauthorized switch-on.

Wait for one minute at standstill.

Check the oil level.

If necessary, top up oil of the same oil type and 

the same brand up to the maximum level.

7.3 Oil change

Warning:

Rotating, pressurized and hot components, 

DANGER OF INJURY

The oil change may only be carried out at a stand-

still and with the screw compressor air end system 

completely discharged. 

7.3.1 Oil change intervals

According to the specifications of the system man-

ufacturer. For reference values for the screw com-

pressor air ends, see chapter 7.5 "Maintenance 

intervals".

Summary of Contents for EVO15





































Reviews: