background image

Operating Manual - 

EVO

®

 Line

[en] 07/2020

5.5

5.7 Air outlet

The pressure loss at the air outlet due to air after-

coolers, fittings, piping, etc.should be as small as 

possible.

Note:

Cross-sections of the outlet pipe must be gener-

ously dimensioned. Avoid pressure losses due to 

elbow screw fittings. 

The outlet pipe must be connected stress-free to 

the outlet.

Warning:

Serious injuries and damage are possible in case 

of operation without a safety valve!

Operation without a safety valve on the separator 

tank is not permitted.

Note:

A possible compressed air temperature (at the 

outlet) of up to 110°C/230°F requires the compo-

nents connected downstream, e.g. the com-

pressed-air hose, pressure switch, air after-cooler, 

fittings, etc. to be designed for this temperature.

We therefore recommend the installation of an air 

after-cooler.

When used without an air after-cooler, the high 

outlet temperature must be pointed out to the final 

customer.

5.8 Oil cooling

Note:

The cooler connection lines must be connected 

torque-free to the oil connections.

The following information on the design and exe-

cution of the oil cooling system must be observed.

– The oil cooling system must be designed so 

that the oil outlet temperature is a maximum of 

105°C/220°F at the maximum intended ambi-

ent temperature.

– The oil circulation quantity is dependent on the 

pressure difference between the outlet and the 

inlet pressure of your application.

– The oil cooler must be installed so that it can be 

cleaned easily.

– When designing the cooling system, the pres-

sure dew point graph (Figure 8-1) must be 

taken into account.

If questions arise concerning the pressure dew 

point, please contact ROTORCOMP.

5.9 Service

 

Ensure good accessibility to the service points 

when installing the screw compressor air end sys-

tem in a housing:

– Oil filling point

– Oil drain point

– Removal of the separator cartridge (removal 

dimensions according to offer drawing) 

– Removal of the oil filter cartridge (observe the 

removal dimensions specified in the offer draw-

ing) 

– Easy cleaning of the oil cooler

– Replacement of the shaft seal (removal and 

installation of the end cover and the bearing 

race)

– Belt drive (accessibility, specifications for cor-

rect belt tension)

Summary of Contents for EVO15





































Reviews: