Rossum Control Forge Operation Manual Download Page 49

Page: 49 / 70

The

Utilities

menu is
where you’ll
find Control
Forge’s
various
housekeeping
and
maintenance
functions.

To access
the

Utilities

menu, press
and hold
the

Global/

Pause/
Utilities

button while
in

Play Mode

Turn the
encoder to
scroll through
the available
function list.
Click the

encoder to choose the desired function.

The menu is dismissed by pressing the

Global/Pause/Utilities

button again.

Here are the available

Utility

functions:

Send to Module

This function
lets you send
all of the
presets and
sequences in
your Control
Forge to
a Satellite
module or
another
Control
Forge.

To send the data:
1. Connect the

Trigger 2

output from your

Control Forge to the

Logic

input of the

receiving module

2. Select

Utilities > Send to Module

on your

Control Forge.

3. Select

Utilities

Receive From Module

on the receiving module, then click the
receiving module’s encoder.

4. Click the encoder on your Control Forge.

The display will show the progress of the
transfer.

5. If an error is detected on the receiving

module during reception or on
completion of reception, an error
message will be displayed there and you

can press
the sending
Control
Forge’s
encoder to try
again or press
the

Global

Pause/
Utilities

button to exit.

18. Utilities

Summary of Contents for Control Forge






































































Search results

Summary of Contents for Control Forge

Reviews:

Brands by name

Popular brands

Rossum Control Forge, Operation Manual

Search results

Summary of Contents for Control Forge

Reviews:

Brands by name

Popular brands