Rosslare AC-225 PCBA Installation And User Manual Download Page 38

Page: 38 / 45

Communications

RS-232

MD-N32

Access
Control

Panel

LAN/WAN

Figure 19: MD-N32 Configuration connecting a single panel

When using an MD-N32, for a single panel, either an RS-232

cable or Rosslare's MD-14 RS-485 converter can be used.
To connect an MD-N32 to more than one panel (up to 32

panels), Rosslare's MD-14 RS-485 converter must be used.
Connect the MD-14 between the RS-485 access control panel

network and the MD-N32 converter.

RS-232

MD-N32 TCP/IP/

RS-232 Converter

MD-14 RS-232/

RS-485 Converter

RS-485

Access
Control

Panel #1

Access
Control

Panel #2

LAN/WAN

Figure 20: Connecting Multiple Access control panels with MD-N32

The MD-14 is not required when using the AC-225IP.

AC-225IP

RS-485

Access
Control

Panel #1

Access
Control

Panel #2

LAN/WAN

Figure 21: Connecting Multiple Access control panels with AC-225IP

Note:

For more information on operating an MD-N32, refer to
the MD-N32 User Manual.

AC-225 Hardware Installation and User Guide

Page 37

Summary of Contents for AC-225 PCBA














































Search results

Summary of Contents for AC-225 PCBA

Reviews:

Related manuals for AC-225 PCBA

Brands by name

Popular brands

Rosslare AC-225 PCBA, Installation And User Manual

Search results

Summary of Contents for AC-225 PCBA

Reviews:

Related manuals for AC-225 PCBA

Brands by name

Popular brands