Rosslare AC-225 PCBA Installation And User Manual Download Page 39

Page: 39 / 45

Communications

6.3

Modem Network Connection

Access control panels can be controlled from the computer's
modem. The modem is assigned from within the VeriTrax AS-

225 software.
Use a modem when the access control panel is too far from
the computer to use a serial connection and an alternative RS-

232/RS-485 network or TCP/IP network is unavailable.
The following diagram illustrates remote site modem

configuration with AC-225.

RS-232

MD-N33

Modem/RS-232

Converter

Telephone

Line

MD-N33

Modem/RS-232

Converter

RS-232

RS-485

Access
Control
Panel

MD-14 RS-232/RS-485

Converter

Figure 22: Remote Site Modem Configuration

Note:

For more information on modem connections, refer to the
MD-N33 User Manual and the AS-225 software manual.

Hardware Requirements

•

2 Standard Telephone cables – RJ11 plugs in both sides

•

Crossed 9 pin RS-232 cable (female jack on both sides)

•

Rosslare MD-14 (RS-232 to RS-485 converter)

•

2 Rosslare MD-N33 (Modem to serial gateway)

•

Rosslare AC-225 panel

AC-225 Hardware Installation and User Guide

Page 38

Summary of Contents for AC-225 PCBA














































Search results

Summary of Contents for AC-225 PCBA

Reviews:

Related manuals for AC-225 PCBA

Brands by name

Popular brands

Rosslare AC-225 PCBA, Installation And User Manual

Search results

Summary of Contents for AC-225 PCBA

Reviews:

Related manuals for AC-225 PCBA

Brands by name

Popular brands