manualshive.com logo in svg

Rosemount P300, Installation And Operation Manual

Share
Download
Rosemount P300 Installation And Operation Manual Download Page 18

Rosemount Model P300 Pressure Validator

3-4

Setting Main Display Mode

FIGURE 3-2. Typical Main Display in 
Voltage Mode.

Set Pressure as Main Display

Press the 

P

 key once. A beep will sound and the display will change.

Set Current as Main Display

Press the 

I

 key once. A beep will sound and the display will change.

Set Voltage as Main Display

Press the 

V

 key once. A beep will sound and the display will change.

NOTE

MAIN

 

DISPLAY

: 

PRESSURE

 is the default display mode when the validator 

is shipped from the manufacturer.

Setting Dual Display Mode

FIGURE 3-3. A Typical Dual Display 
with Pressure in Main Display and 
Voltage in Secondary Display.

Set Pressure as Main Display with Voltage as Secondary Display

Press the 

V

 and 

P

 keys together. A beep will sound and the display will 

change.

Set Pressure as Main Display with Current as Secondary Display

Press the 

I

 and 

P

 keys together. A beep will sound and the display will 

change. 

Zeroing the Display

The 

ZERO

 key is used to zero displays in all calibration modes. Zeroing 

should be done before all calibrations to ensure correct readings.

To zero a display

Press the desired function key and 

ZERO

 simultaneously. A beep sounds 

and the secondary display reads 

ZEROING

__

.

 If the instrument is in a 

different mode than the one being zeroed, the secondary display reads 

INCORRECT

 

MODE

.

P

300

_0

7A

P

300

_08

A

Summary of Contents for P300

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands