Rosemount 848T Reference Manual Download Page 3

Page: 3 / 60

Reference Manual

00809-0100-4848, Rev AA

July 2009

Rosemount 848T Wireless

www.rosemount.com

Rosemount 848T Wireless
Temperature Transmitter

Rosemount 848T Wireless Temperature Transmitter may be protected by one or more U.S.

Patents issued or pending. Other foreign patents issued or pending.

Rosemount 848T Wireless Hardware Revision
HART

Device Revision

Field Communicator Field Device Revision

2
2
Dev v2, DD v1

NOTICE

Read this manual before working with the product. For personal and system safety, and for

optimum product performance, make sure to thoroughly understand the contents before

installing, using, or maintaining this product.
The United States has two toll-free assistance numbers and two international numbers.

Customer Central

United States: 1 800 999 9307

Asia Pacific: 65 77 8211

Europe/Middle East/Africa: 49 8153 9390

National Response Center

1 800 654 7768 (24 hours a day)

Equipment service needs

The products described in this document are NOT designed for nuclear-qualified

applications.
Using non-nuclear qualified products in applications that require nuclear-qualified hardware

or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact a Emerson Process

Management Sales Representative.

Summary of Contents for 848T





























































Search results

Summary of Contents for 848T

Reviews:

Related manuals for 848T

Brands by name

Popular brands

Rosemount 848T, Reference Manual

Search results

Summary of Contents for 848T

Reviews:

Related manuals for 848T

Brands by name

Popular brands