Rosemount 848T Reference Manual Download Page 51 | Manualshive

Page: 51 / 60

background image

Reference Manual

00809-0100-4848, Rev AA

July 2009

Rosemount 848T Wireless

www.rosemount.com

Appendix B

Product Certifications

Approved Manufacturing Locations  . . . . . . . . . . . . . . . . . page B-1
Telecommunication Compliance  . . . . . . . . . . . . . . . . . . . . page B-1
FCC and IC   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B-1
European Union Directive Information  . . . . . . . . . . . . . . . page B-2
Ordinary Location Certification for FM . . . . . . . . . . . . . . . page B-2
Hazardous Locations Certificates . . . . . . . . . . . . . . . . . . . page B-2

Approved Manufacturing
Locations

Rosemount Inc. - Chanhassen, Minnesota, USA

Emerson Process Management GmbH & Co. - Karlstein, Germany

Emerson Process Management Asia Pacific Private Limited - Singapore

Telecommunication
Compliance

All wireless devices require certification to ensure that they adhere to

regulations regarding the use of the RF spectrum. Nearly every country

requires this type of product certification. Emerson is working with

governmental agencies around the world to supply fully compliant products

and remove the risk of violating country directives or laws governing wireless

device usage.

FCC and IC

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following conditions: This device may not cause harmful interference, this

device must accept any interference received, including interference that may

cause undesired operation.
This device must be installed to ensure a minimum antenna separation

distance of 20 cm from all persons.

«
...
49
50
51
52
53
...
»

Summary of Contents for 848T





























































Reviews:

No comments

Related manuals for 848T

Brand: Napoleon Pages: 3

Brand: Icom Pages: 116

Brand: DB Elettronica Telecomunicazioni Pages: 19

Brand: Simrad Pages: 52

Brand: DAELIM Pages: 35

Efector 600 TADx91 Series

Brand: IFM Electronic Pages: 25

Brand: M-system Pages: 2

Brand: Moxa Technologies Pages: 18

Brand: SEIKAKU TECHNICAL GROUP Pages: 6

Brand: Clas Ohlson Pages: 5

Brand: Cobra Pages: 11

Brand: Cobra Pages: 42

Brand: Vertex Standard Pages: 5

Brand: Shearwater Pages: 19

Brand: Eddystone Pages: 34

Multi Tasker MT103-122

Brand: Altinex Pages: 19

Brand: Altera Pages: 702

Brand: CYP Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands