Roofit.Solar Double Seam Installation Manual Download

Page: 3 / 17

Double Seam Installation Manual

Installation Roof Accessories

Ridge cap

Chimney flashing

Valley flashing

Window flashing

Gable border

Eave flashing

Ridge caps are designed

to cover the ridge of

the roof and shield

against seepage.

Ridge Cap

Valley flashings are

installed before

the profile sheet

and followed by

the roof slates.

Valley Flashing

Chimney flashings are

used to join the roof

sheet and chimney

together, ensuring

that the roof

repels water at the

base of the chimney.

Chimney Flashing

Gable borders are

attached to the board

of the end eave,

finishing the edge

of the roof and

protecting it from

dampness.

Gable Border

Eave flashings

carry rainwater

from the roof to

the gutter.

Eave Flashing

Please read Roofit.solar Safety Manual cerafully before initiating any Roofit.solar system installation.

Summary of Contents for Double Seam


















Search results

Summary of Contents for Double Seam

Reviews:

Related manuals for Double Seam

Brands by name

Popular brands

Roofit.Solar Double Seam, Installation Manual

Search results

Summary of Contents for Double Seam

Reviews:

Related manuals for Double Seam

Brands by name

Popular brands