background image

RONK Automatic Transfer Switch Owner’s Manual 

29

WARRANTY

AUTOMATIC TRANSFER SWITCH
OWNER WARRANTY POLICY

LIMITED WARRANTY

RONK Electrical Industries, Inc. will repair or replace, free 
of charge, any part(s) of the equipment that is defective in 
material or workmanship or both providing that installation 
of the equipment complies with all applicable codes, industry 
standards, laws, regulations and provided installation manual. 
RONK’s ATS and associated components shall be installed only 
by a licensed electrical contractor, and otherwise this warranty 
is void. This warranty is effective for the time period and subject 
to the conditions stated below. For warranty service, please call 
RONK Electrical Industries, Inc. at 1-217-563-8333.

THERE ARE NO OTHER EXPRESS WARRANTIES OR IMPLIED 
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE. THE ABOVE WARRANTY IS 
LIMITED TO TWO YEARS FROM PURCHASE. ANY AND ALL IMPLIED 
WARRANTIES ARE EXCLUDED AND LIABILITY FOR INCIDENTAL 
OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT 
EXCLUSION IS PERMITTED BY LAW. BUYER’S SOLE REMEDY IS THE 
LIMITED WARRANTY STATED ABOVE.

This warranty only applies to units sold for use in the United 
States of America and Canada.

WARRANTY PERIOD

Consumer Use: 2 years 
Commercial Use: 2 years

The warranty period begins on the date of purchase by the first 
retail consumer and continues for the period stated above. 
Equipment used for primary power in place of utility is not 
applicable to this warranty.

WARRANTY REGISTRATION PROCESS

Thank you for choosing RONK’s Automatic Transfer Switch for 
your generator system!

1. For the fastest and most efficient way to register your ATS 

warranty, please complete the online form at ronkelectrical.
com/warranty (preferred method). Otherwise, please complete 
the postcard and return via mail.

2. Complete the online form or return the postcard within 10 

days of installation.

3. Save the proof of purchase. If your switch is not registered 

within 10 days, the warranty start date will default to the date 
of purchase by the first retail consumer.

4. If the warranty registration steps are not completed, the 

warranty start date will default to the manufacturing date.

ABOUT OUR WARRANTY

Warranty repairs are handled routinely, but sometimes requests 
for warranty service may not be appropriate or applicable. For 
example, warranty service would not apply if equipment damage 
occurred because of misuse, lack of routine maintenance, 
shipping, handling, warehousing, or improper installation.

Similarly, the warranty is void if the manufacturing date or the 
serial number on the equipment has been removed, altered, 
or modified. During the warranty period defined above, the 
authorized certified technician, at its option, will repair or replace 
any part that, upon examination, is found to be defective under 
normal use and service. No allowances shall be made to the 
Buyer for any transportation, duties, brokerage fees, labor costs, 
or parts adjustments or repairs, or any other work, unless said 
charges have been authorized in writing, in advance, by the 
Seller. The Seller shall not be liable for determining whether 
any Article(s) or parts thereof are suitable for the Buyer’s or any 
third-party’s intended use or application. The Seller shall in no 
event be liable for any special or consequential damages or for 
loss of profit as a result of a breach of this warranty, including 
without limitation, any damages relating to any direct or 
indirect damage to property resulting from any use, removal or 
installation of the article(s) by the Buyer or any third-party.

This warranty will not cover the following repairs and equipment:

• Normal Wear: Electrical equipment, like any mechanical device, 

needs periodic parts and service to perform well. This warranty 
does not cover repair when normal use has exhausted the life 
of the part or equipment.

• Installation and Maintenance: This warranty does not apply to 

equipment or parts that have been subjected to improper or 
unauthorized installation or alteration or modification, misuse, 
negligence, accident, overloading, improper maintenance, 
repair or storage so as, in our judgment, to adversely affect its 
performance and reliability. This warranty also does not cover 
normal maintenance such as adjustments, cleaning and fuse 
replacement.

Other exclusions: This warranty excludes wear items or damage 
or malfunctions resulting from accidents, abuse, modifications, 
alterations, or improper servicing. Accessory parts are excluded 
from the product warranty. This warranty excludes failure due 
to acts of God and other force majeure events beyond the 
manufacturer’s control. Also excluded is used, reconditioned, 
and demonstration equipment. The warranty shall not apply 
to any materials or parts thereof furnished by the Buyer, or 
acquired from others at the Buyer’s request and/or the Buyer’s 
specifications or designs.

Summary of Contents for 100-600 AMP

































Reviews: