background image

21 

 

6.1 WARNING SAFETY MEASURES FOR THE USER 

The place where the boiler is to be set up, called the mounting place, must be prepared by local, national, 
and European regulations.  

The boiler is a “heating machine" and while it is on 

it has outer surfaces that are very hot or that 

achieve very high temperatures.

  

This boiler is designed to burn fuel from pressed wood mass (a pellet with a diameter of 5 mm to 6 mm, 
with the length of 30 mm, with maximum moisture 8-9%).  

It is therefore very important to pay attention to the following when the boiler is on:  

  

 

Do not approach and touch the glass on the door, there is a BURNING HAZARD  

 

Do not approach and touch the smoke drain pipe, there is a BURNING HAZARD  

 

Do not do any cleanups  

 

Do not open the door because the boiler is working properly only when it is sealed  

 

Do not throw away the ashes when the boiler is ON 

 

Children and pets need to stand away from the boiler  

 

FOLLOW ALL INSTRUCTIONS GIVEN IN THIS MANUAL  

Likewise, the proper use of biofuel pellets means:

  

 

Only use the fuel that meets the manufacturer's instructions,  

 

Always follow the maintenance plan for the boiler,  

 

Clean the boiler every day (only when the boiler and the ash are cold),  

 

Do not use the boiler in case of any defects or abnormalities, in the case of unusual noise and/or 
suspected faults,  

 

Do not spray water on the boiler, even when firefighting,

  

 

Do not turn off the boiler by pulling the plug.

 

Use the button on the board to turn off,

 

 

Do not tilt the boiler, IT MAY BECOME UNSTABLE, 

 

Do not use the boiler as a support or a holder. Never leave the tank lid open.  

 

Do not touch the dyed parts of the boiler while it is ON, 

 

Do not use wood or coal as a fuel, 

but only the pellet

 with the following characteristics: diameter 

of 5--6 mm, maximum length 30 mm, maximum moisture content 8-9%,  

 

Do not use the boiler to burn waste,  

 

Always perform all operations with maximum security measures.  

7. SAFETY GUIDILINES FOR IGNITION AND CLEANING OF THE STOVE  

 

For turning the boiler ON never use gasoline, kerosene or any other flammable liquid. Keep these 
types of fluid away from the boiler while it is running,  

 

Never turn the boiler ON if the glass is damaged. Do not strike the glass or the door so that they 
do not get damaged, 

 

While the boiler  is ON, do not open the door to clean the glass. Clean the glass only when the 
boiler is cold, using a cotton cloth or paper towel and a glass cleaner, 

 

Make sure the boiler is installed and secure to prevent any movement,  

 

Make sure that the ash box is inserted and that it is fully closed, so that the doors are leaning 
properly on the box, 

 

Make sure the boiler door is firmly closed while the stove is ON, 

 

Use a vacuum cleaner to pull the ashes from the boiler only when the boiler is completely cold, 

 

Never use abrasive cleaners for cleaning the surface of the boiler. 

7.1 REGULAR CLEANING AND MAINTENANCE OF THE BOILER(FOR USER) 

 

Summary of Contents for SM ECO 25

























































Reviews: