Romstal SM ECO 25 Instructions For Use, Maintenance And Installation Manual Download

Page: 6 / 56

COMPACT 33:

NAME

VALUE

UNIT

Dimension

720 x 950 x 1475

Mass

285

Thank capacity

The door of the tank

610 x 320

Water capacity of the boiler

Cleaning door

260 x 200

NAME

VALUE

UNIT

Installation place

4.22

The height from the floor to axis of the flue

terminal

210

The height from the floor to axis of the hot water

terminal

1145

The height from the floor to axis of the cold water

terminal

565

The height from the floor to axis of the

(filling/emptying) terminal

565

Flue terminal diameter

Diameter of exterior air intake on the wall

Diameter of the hot water terminal

1”

col

Diameter of the cold water terminal

1”

col

Diameter of the (filling/emptying) terminal

1/2

col

Voltage and frequency

220 /5/50

V/A/Hz

NAME

VALUE

UNIT

The power of the water heater

at (min/max) power

9.0 – 30.0

Heating volume

220

Water pressure

1.5 – 2.5

bar

Water temperature

65 – 80

˚C

Flue temperature

∼

160

˚C

Optimal draft

0.05 – 0.1

mbar

The main/max consumption

2.1 – 6.2

kg/h

Volume of expansion vessel

---

Pump power (max)

Summary of Contents for SM ECO 25

























































Search results

Summary of Contents for SM ECO 25

Reviews:

Related manuals for SM ECO 25

Brands by name

Popular brands

Romstal SM ECO 25, Instructions For Use, Maintenance And Installation Manual

Search results

Summary of Contents for SM ECO 25

Reviews:

Related manuals for SM ECO 25

Brands by name

Popular brands