background image

TROUBLE SHOOTING GUIDE

Some important information to help you Maintain your product.

The following information is all you need to keep your product looking new.

Clean your product using a mild detergent diluted in water and then polished off using a soft cloth.

If you live in a hard water area, periodically clean your product using a 50/50 solution of white vinegar and water.  The 

solution should be left on the enclosure for approximately 5 minutes then rinsed off using warm water. This method of 

cleaning should remove lime scale residue.

Simple Maintenance

Our products are generally maintenance free, however it may be necessary to lubricate wheel assemblies and other 

moving parts from time to time.

It is strongly recommended that a quality silicone spray is used.

A list of Don’t’s:

1.  Don’t use acidic based products which are unsuitable for cleaning enamel surfaces.

2. 

Don’t use abrasive cleaners or cleaners using bleach or solvents, these products will adversely affect the finish of 

the aluminium profiles.

3.  Don’t use scouring pads, powder or any sharp instruments when cleaning the enclosure.

Should you experience any problems during installation please refer to the

Trouble Shooting Guide or contact Customer Relations on:

+44 (0) 1325 328033

To enable customer relations to provide you with an excellent level of service it is important that you

quote your product Code and Reference Number - these can be found on the Guarantee card.

Problem

Solution

Leaking

1. 

Check that the inside gap between the Tray and Wall Profiles has been sealed correctly.

2.  Ensure the tray is sealed along the tiled walls prior to installation.

3.  If the inside joint between the enclosure and the tray top is sealed, this will cause 

leakage - sealant must be removed.

4. 

Ensure the Wall Profiles on the tiled walls are sealed both vertically inside and outside.

5.  Ensure the joint between the enclosure and tray top is sealed.

6. 

The deflector on the Bottom Seals is semi rigid and can be carefully altered to offer 

more deflection of the water.

7.  Check the Angled Magnets are locating and there are no gaps.

Important: This enclosure should be water tested conforming to BS EN 14428

Enclosure Alignment

on the Tray

1. 

Is the enclosure fitted onto a tiled wall?

2. 

Check the Wall Profiles are in line with each other and parallel to the tray?

3. 

Are the Wall Profiles completely vertical?

Door not operating

correctly 

1. 

Ensure both Wall Profiles are completely vertical.

2.  Ensure the tray is completely level.

Summary of Contents for N2F7613S










Reviews: