The amount of condensation that forms is influenced by the temperature and
humidity of the room air. Recommended values in continuous operation:
30 °C (86 °F): 80 % r. h. = approx. 80 litres/day, 60 % r. h. = approx. 40 litres/day
20 °C (68 °F): 80 % r. h. = approx. 40 litres/day, 60 % r. h. = approx. 22 litres/day
15 °C (59 °F): 80 % r. h. = approx. 28 litres/day, 60 % r. h. = approx. 16 litres/day
10 °C (50 °F): 80 % r. h. = approx. 16 litres/day, 60 % r. h. = approx. 11 litres/day
(r. h. = relative humidity)
Water residue can drip from the condensation drain hose (4) after dehumidifi-
cation/drying.
4. Maintenance
4.1. Maintenance
WARNING
Pull out the mains plug before maintenance work!
Clean the ROLLER’S Scirocco 80 regularly especially when it has not been in
use for a long time. Store the device in a frost-proof location. Empty and clean
the 11.5 l condensation tank (9).
Clean the air filter mat regularly. To do this, pull the air filter flap (17) which is
fastened by a magnet. Pull out the wire rods. Clean the air filter mat and the
air filter flap (17) for example with a suitable vacuum cleaner or under running
water. Renew the air filter mat if necessary. Allow the air filter mat and air filter
flap (17) to dray before re-assembling.
Clean plastic parts (e.g. housing) only with machine cleaner (Art. No. 140119)
or a mild soap and a damp cloth. Do not use household cleaners. These often
contain chemicals which can damage the plastic parts. Never use petrol,
turpentine, thinner or similar products for cleaning.
Make sure that liquids never get inside the device.
4.2. Inspection/Repair
WARNING
Pull out the mains plug before carrying out maintenance or repair work!
This work may only be performed by qualified personnel.
eng eng
5. Faults
5.1. Fault: ROLLER’S Scirocco 80 does not start.
Cause:
Remedy:
● Power cable defective.
● Change power cable.
● Device defective.
● Have the apparatus checked/repaired by an authorised ROLLER customer
service workshop.
● The humidity set on the device is higher than the humidity in the room.
● No dehumidification necessary or correct the humidity setting on the device,
see 3. Operation
● 11.5 l condensation tank (9) (accessory, Art. No. 132100) was inserted
incorrectly in the ROLLER’S Scirocco 80.
● See 2.4.
● Condensation tank switch set incorrectly (5).
● See 2.3. and 2.4.
5.2. Fault: On reaching the humidity set on the ROLLER’S Scirocco 80, the device does not switch on or off.
Cause:
Remedy:
● The controller only switches the device on/off when the humidity exceeds/
drops below the set humidity by 3 %.
● Wait or correct the humidity setting on the device, see 3.
● Continuous operation is set.
● Change the operating mode, see 3.
5.3. Fault: ROLLER’S Scirocco 80 switches off although the humidity set on the device has not yet been reached.
Cause:
Remedy:
● In cold ambient temperatures and/or in continuous operation, the unit can
ice up, the icing symbol (18) is shown in the display (2).
● The device is equipped with an automatic hot gas thawing system.
This is regulated by the device. The device starts the dehumidification/drying
automatically after thawing, the icing symbol (18) switches off. Switch off the
ROLLER’S Scirocco 80 if icing occurs at short intervals. Wait until the ice has
thawed completely. Then continue dehumidification/drying.
● Power cable defective.
● Change power cable.
● Device defective.
● Have the device checked/repaired by an authorised ROLLER customer service
workshop.
5.4. Fault: The dehumidification performance diminishes.
Cause:
Remedy:
● Air filter mat/air filter flap (17) soiled.
● Clean/replace parts, see 4.1. Maintenance
● Using ROLLER’S Scirocco 80 reduces the humidity, this also reduces the
amount of condensation.
● Check whether the dehumidification/drying can be set.
5.5. Fault: Error messages E1 or E3 are shown in the display (2).
Cause:
Remedy:
● The humidity of the room is outside the measuring range ≤ 30 % or ≥ 90 %
of the ROLLER’S Scirocco 80.
● Set the device to continuous operation, see 3. Operation
● Sensor for measuring the humidity is defective.
● Have the device checked/repaired by an authorised ROLLER customer service
workshop.
5.6. Fault: Error messages E2 or E5 are shown in the display (2).
Cause:
Remedy:
● Sensor for compressor temperature monitoring is defective.
● Have the device checked/repaired by an authorised ROLLER customer service
workshop.
5.7. Fault: Error message E4 is shown in the display (2).
Cause:
Remedy:
● 11.5 l condensation tank (9) (accessory, Art. No. 132100) is full.
● Empty the 11.5 l condensation tank.
● Condensation tank switch set incorrectly (5).
● See 2.3. and 2.4.
9