Roland Cakewalk A-500S Owner'S Manual Download

Page: 63 / 80

Troubleshooting

Did you log on to Windows with the appropriate user privileges?

You must log onto Windows using one of the following user names.

• A user name belonging to the Administrators group, such as Administrator

• A user name whose account type is Computer Administrator

* For details, ask the system administrator for your computer.

In some cases, you may be unable to install the driver because of the “Driver signing option” settings.

Refer to

“Driver signing option settings (Windows XP)”

(p. 54) and make the appropriate settings.

Could other software be running, perhaps in the background (such as anti-virus software)?

The installation may not occur correctly if other software is running. Be sure to close all other software before you
perform the installation.

Could the A-500S’s [ADVANCED DRIVER] switch be OFF?

Turn the A-500S’s [ADVANCED DRIVER] switch

, and install the driver once again.

After you connect the A-500S, it may take several tens of seconds or several minutes before it is
recognized by your computer.

This is not a malfunction.

Please wait until the Found New Hardware Wizard appears.

Is the A-500S connected?

Make sure that the A-500S is correctly connected to your computer.

Could your computer be operating on its battery?

Operation may be unstable if your computer is operating on battery power.

Please use your computer with its power supply connected.

Could you be using a bus-powered USB hub (a hub that does not require a power supply)?

The A-500S cannot be used with a bus-powered USB hub (a hub that does not need a separate power supply). Use it
with a self-powered USB hub (a hub that has an internal power supply or AC adaptor).

Could a USB device other than a mouse or keyboard be connected?

Disconnect all USB devices (other than a mouse and keyboard, if used) from your computer before performing the
installation.

Check the power management settings of your computer.

Your computer’s power management settings may be limiting the power that is supplied to USB.

Take a look at your computer’s power management settings.

➝

“Power management settings”

(p. 57)

Can’t install the driver according to the procedure

Installation is not successfully completed when you connect the A-500S

A-500S_e.book 63 ページ２０１０年２月１９日　金曜日　午後８時３分

Summary of Contents for Cakewalk A-500S

















































































Search results

Summary of Contents for Cakewalk A-500S

Reviews:

Related manuals for Cakewalk A-500S

Brands by name

Popular brands

Roland Cakewalk A-500S, Owner'S Manual

Search results

Summary of Contents for Cakewalk A-500S

Reviews:

Related manuals for Cakewalk A-500S

Brands by name

Popular brands