Roland Cakewalk A-500S Owner'S Manual Download Page 19

Page: 19 / 80

Driver Installation and Settings

In order to use the A-500S with your software, you must select the A-500S as MIDI input/output device. For details on
how to make this setting, refer to the documentation for the software you’re using.

* If you’re unable to select the A-500S as the input/output device in your software, it may be that a problem has

occurred. Refer to

“Problems with settings”

(p. 65) in the Troubleshooting section.

MIDI OUT device

Settings when using the A-500S in Windows Media Player

Some software, such as Windows Media Player, may use the system default playback/recording device as its MIDI
input/output device.

Make the following settings if you want to use an external MIDI sound module connected to the MIDI OUT connector
of the A-500S.

Open the

Control Panel

, click

Sounds, Speech, and Audio Devices

, and then double-click the

Sounds

and Audio Devices.

* If you’re using the Classic view, double-click the

Sounds and Audio Devices

icon.

Click the

Audio

tab to open it, and in the

MIDI Music Playback

area, select

A-500S MIDI OUT

Click

[OK]

to complete the setting.

This completes driver installation and settings.

Input/output device settings

MIDI output device

A-500S MIDI OUT

MIDI input device

A-500S

Caution when recording or playing back with your software

Check the following points before you use the A-500S to record or play back.

• Connect the A-500S to your computer before you start up the software you’re using.

• Do not disconnect the A-500S’s USB cable from your computer while your software is running. Close the software

you’re using before you disconnect the A-500S’s USB cable from your computer.

A-500S_e.book 19 ページ２０１０年２月１９日　金曜日　午後８時３分

Summary of Contents for Cakewalk A-500S

















































































Search results

Summary of Contents for Cakewalk A-500S

Reviews:

Related manuals for Cakewalk A-500S

Brands by name

Popular brands

Roland Cakewalk A-500S, Owner'S Manual

Search results

Summary of Contents for Cakewalk A-500S

Reviews:

Related manuals for Cakewalk A-500S

Brands by name

Popular brands