Rohde & Schwarz CMW-B400B User Manual Download | Manualshive

Page: 38 / 97

background image

GUI Reference

R&S

®

CMW-B400B/-B405A

38

User Manual 1176.8116.02 ─ 04

Statistic Count

............................................................................................................... 38

.................................................................................................................. 38

.............................................................................................................................. 38

.......................................................................................................................... 38

Statistic Count

Configures the statistic count for multitone measurements. This parameter can also be
configured within the general settings, see

chapter 4.3.1, "General Settings (Analog)"

chapter 4.3.2, "General Settings (Digital)"

Remote command:

CONFigure:AUDio:MEAS<i>:ANALog:MULTitone:SCOunt
CONFigure:AUDio:MEAS<i>:DIGital:MULTitone:SCOunt

Result Mode

Selects the display mode for the multitone results. You can display the levels of the
individual test tones as absolute levels (dBV or dBFS) or as levels relative to a
selected test tone (dB).

Remote command:

CONFigure:AUDio:MEAS<i>:ANALog:MULTitone:RMODe
CONFigure:AUDio:MEAS<i>:DIGital:MULTitone:RMODe

Filter

The settings configure the individual filter stages of the AF analyzer. For a description
of the filter types see

chapter 3.3, "AF Filter Settings"

Remote command:
Analog measurement:

CONFigure:AUDio:MEAS<i>:ANALog:MULTitone:FILTer:LPASs
CONFigure:AUDio:MEAS<i>:ANALog:MULTitone:FILTer:HPASs
CONFigure:AUDio:MEAS<i>:ANALog:MULTitone:FILTer:WEIGhting

Digital measurement:

CONFigure:AUDio:MEAS<i>:DIGital:MULTitone:FILTer:LPASs
CONFigure:AUDio:MEAS<i>:DIGital:MULTitone:FILTer:HPASs
CONFigure:AUDio:MEAS<i>:DIGital:MULTitone:FILTer:WEIGhting

Display

These settings configure the axes of the multitone result bar graph and select which
traces shall be displayed.

These settings can also be accessed via hotkeys, see

chapter 3.4.4, "Modifying Dia-

Remote command:
n/a

4.3.5 FFT Noise Settings

The following settings are specific for FFT noise measurements. They can be config-
ured separately for analog and digital measurements. The description applies to both.

Audio Measurement Settings

深圳德标仪器

135-1095-0799

«
...
36
37
38
39
40
...
»

Summary of Contents for CMW-B400B


































































































Reviews:

No comments

Related manuals for CMW-B400B

DigitalFlow GF868

Brand: GE Pages: 80

Brand: A&D Pages: 74

Brand: E Instruments Pages: 2

Brand: OHAUS Pages: 84

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: Hammond Organ Pages: 25

Brand: Hammond Organ Pages: 87

Brand: i-SENS Pages: 50

Brand: MadMan Pages: 37

Brand: MADDALENA Pages: 5

Brand: Sanmenxia Pages: 17

Brand: SANKO Pages: 25

Brand: Samson Pages: 2

Brand: Fluke Biomedical Pages: 28

Brand: VOLTCRAFT Pages: 108

Brand: Wetekom Pages: 22

Brand: MICRO-EPSILON Pages: 82

Brand: Kirby Morgan Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands