background image

GAHP-AR – Installation, start-up, use and maintenance manual 

94

 

 Edition: 

2014-08 

E 644 

EVAPORATOR TEMPERATURE SENSOR DEFECTIVE 

CODE GENERATED BY

Fault (interruption or short circuit) on evaporator temperature sensor. 

RESET METHOD

Reset may be performed via S61 board, menu 2, Parameter 1 (or via DDC). If the code persists, contact 
Robur TAC.

 

U

 646 

HIGH HOT INLET WATER TEMPERATURE 

CODE GENERATED BY

Hot inlet water temperature higher than upper operating limit of the appliance (if the appliance is in 
operation). 

RESET METHOD

Reset occurs automatically when the condition that generated the code ceases. If the code persists, 
contact Robur TAC.

 

U

 647 

LOW HOT INLET WATER TEMPERATURE 

CODE GENERATED BY

Hot water temperature lower than lower operating limit of the appliance (if the appliance is in operation). 

RESET METHOD

Reset occurs automatically when the condition that generated the code ceases. If the code persists, 
contact Robur TAC.

 

E 647

 

LOW HOT INLET WATER TEMPERATURE 

CODE GENERATED BY

U

 

647

 

code generated 3 times in 1 hour with the circulator on. 

RESET METHOD

In " Heating mode", reset occurs automatically when the condition that generated the code ceases. If the 
code persists, contact Robur TAC

U

 648 

HIGH HOT WATER DIFFERENTIAL TEMPERATURE 

CODE GENERATED BY

High hot water differential temperature. 

RESET METHOD

Reset occurs automatically 20 minutes after the code is generated. If the code persists, code E648 may 
occur (in this case, contact Robur TAC).

 

E 648 

HIGH HOT WATER DIFFERENTIAL TEMPERATURE 

CODE GENERATED BY

U

 

648

 

code is generated 2 times in 2 hours of operation. 

RESET METHOD

Reset may be performed via S61 board, menu 2, Parameter 1 (or via DDC). If the code persists, contact 
Robur TAC.

 

E 649 

"AR10" SATELLITE BOARD NOT PRESENT 

CODE GENERATED BY

Satellite board not present. 

RESET METHOD

Reset occurs automatically when the condition that generated the code ceases.

 

U

 

651

 

ANTIFREEZE FUNCTION ACTIVATED – COOLING MODULE 

Activation takes place only if the cold module is off and the antifreeze function is enabled (see menu 1, parameter 77).

 

CODE GENERATED WHEN

Inlet or outlet water temperature of the cold module falls below 39.2°F (the code generated signals that 
the antifreeze function has been activated). 
In this case the antifreeze function activates the plant water circulator. 

RESET METHOD

Reset (deactivation of antifreeze function) occurs automatically when, with only the circulator on, the inlet 
and outlet water temperatures return to over 41°F (in this case the circulator switches off), or if the 
function itself is disabled.

 

U

 652 

DEFROSTING FUNCTION ACTIVATED 

CODE GENERATED BY

Defrosting function activated. 
Defrosting is activated if at least one hour has passed since the last defrosting, if the flame control unit 
has been on for at least 20 minutes, and if ambient temperature, temperature of hot inlet water and of the 
evaporator require its execution. 

RESET METHOD

The code clears automatically when execution of defrosting ends.

 

Summary of Contents for GAHP Line AR Series





































































































Reviews: