manualshive.com logo in svg

RoboteQ Dual Channel Digital Motor Controller AX2550, User Manual, Page: 99 / 186

Share
Download
RoboteQ Dual Channel Digital Motor Controller AX2550 User Manual Download Page 99

AX1500 Motor Controller User’s Manual

99

Power On LED

SECTION 10

Normal and 
Fault Condition 
LED Messages

This section discusses the meaning of the various messages and codes that may be dis-
played on the LED display during normal operation and fault conditions.

Power On LED

The AX1500 features an LED that comes on whenever the board is powered on. When lit, 
this LED indicates that the on-board DC/DC converter is functioning. It provides no infor-
mation regarding the controller’s operation.

Diagnostic LED

The AX1500 features a single diagnostic LED which helps determine the controller’s oper-
ating mode and signal a few fault conditions. The LED is located near the edge of the 
board, next to he 15-pin connector.

Normal Operation Flashing Pattern

Upon normal operation, 1 second after power up, the LED will continuously flash one of 
the patterns below to indicate the operating mode. A flashing LED is also an indication that 
the controller’s processor is running normally.

Summary of Contents for Dual Channel Digital Motor Controller AX2550



























































































































































































Reviews:

No comments