RoboteQ Dual Channel Digital Motor Controller AX2550 User Manual Download Page 15

Page: 15 / 186

AX1500 Motor Controller User’s Manual

SECTION 2

AX1500
Quick Start

This section will give you the basic information needed to quickly install, setup and
run your AX1500 controller in a minimal configuration.

What you will need

For a minimal installation, gather the following components:

•

One AX1500 Controller and its provided cables

•

12V to 40V high capacity, high current battery

•

One or two brushed DC motors

•

One R/C to DB15 connector (provided)

•

Miscellaneous wires, connectors, fuses and switch

Locating the Connectors

Take a moment to familiarize yourself with the controller’s connectors.

Summary of Contents for Dual Channel Digital Motor Controller AX2550


























































































































































































Search results

Summary of Contents for Dual Channel Digital Motor Controller AX2550

Reviews:

RoboteQ Dual Channel Digital Motor Controller AX2550, User Manual, Page: 15 / 186

Search results

Summary of Contents for Dual Channel Digital Motor Controller AX2550

Reviews: