background image

Cut a hole in the worktop that corresponds with the relevant drawing on the previous page.

appliance and any

   surface that is below it.

IMPORTANT

: Do not use a silicon sealant to seal the appliance against the aperture. This will make it

difficult to remove the hob from the aperture in future, particularly if it needs to be serviced.

The

 

minimum

 

clearance

 

from

 

a

 

combustible

 

surface

 

shall

 

be

 

a

 200 

mm

 

horizontal

 

distance

 

from  the

periphery

 

of

 

any

 

gas

 

burner

 (

AS

/

NZS

 5601.1).

IMPORTANT

 :

You

 

must

 

have

 

a

 

gap

 

of

 

at

 

least

 50 

mm

 

between

 

the

 

underneath

 

of

 

the 

5

47

mm

50

mm

Gas

 

Hob

Important information

   

Failure to install the appliance correctly could invalidate  ROBAM APPLIANCES CO.,LTD. guarantee and

   lead to prosecution under the regulations quoted above.

An AUTHORISED PERSON undertake the installation and service work, in compliance with the above

regulations.

The hob must be installed by a qualified person, in accordance with the current edition of the gas safety

(Installation and use) (amendment) regulations and the relevant building/I.E.E. regulations.

Ventilation requirements

The room containing the hob should have an air supply in accordance with the current edition of AS/NZS.5601.1

The room must have opening windows or equivalent; some rooms may also require a permanent vent.

If the room has a volume between 5 and 10m³, it will require an air vent of 50cm²(effective area). Unless it

has a door which opens directly to the outside.

If the room has a volume of less than 5m³, it will require an air vent of 100cm²(effective area).

If it is installed in a room with a volume that exceeds 11m³, then no air vent is required.

If there are any other fuel burning appliance in the same room the current edition of AS/NZS 5601.1 should

be consulted to determine air vent requirements.

Ensure that the room containing the hob is well ventilated, keep natural ventilation holes or install a

mechanical ventilation device(mechanical cooker hood).

Prolonged intensive use of the appliance may call for additional ventilation, either by the opening of a

window

 ,

or

 

by

 

increasing

 

the

 

level

 

of

 

the

 

mechanical

 

ventilation

 

device(where

 

present).

This hob is not fitted with a device for discharging the products of combustion. Ensure that the ventilation

rules and regulations are followed.

Summary of Contents for JZT B110



















Reviews: