21
DIAgNostICs - IN.K 1000 error CoDes
The error codes indicate a failure or problem that must be rectified to guarantee the good function of the
n.YJ2
control
system. The error messages listed below display on the keypad. For more information on error messages.
Please refer to the IN.YE5
control
system techbook at
www.geckodocs.com
If this guide does not help you solve the problem please contact your dealer.
error CoDe
MessAge
AOH
ElEvATEd INTErNAl TEmPErATurE
CFLO
NO FLOw CONdITION
COmm
VerIFy CabLe CONNeCTIONs
er1
swImspa CONFIg. : sLaVe uNIT Is mIssINg
F1
IN.xm2 Fuse # 1 Is bLOwN
F2
IN.xm2 Fuse # 2 Is bLOwN
F3
IN.xm2 Fuse # 3 Is bLOwN
FLC
The pressure swITCh Is CLOsed
FLO
NO FLOw CONdITION FOr mOre ThaN 2 hOurs
FLO
NO FLOw CONdITION
hIbr
add Fresh waTer TO The spa
hL
hIgh LImIT CIrCuIT has TrIpped!
hr
hardware errOr was deTeCTed (ThermaL Fuse)
hr
a hardware errOr was deTeCTed (reLay sTuCk)
LObr
add brOmICharge TO spa waTer
NObr
add brOmICharge TO spa waTer
Oh
spa TemperaTure Is TOO hIgh
pr
Temp prObes Or deTeCTION CIrCuIT are deFeCTIVe
rh Id
IN.xm2 aNd IN.Therm INCOmpaTIbLe
rh NC
COmm. errOr beTweeN IN.xm2 - IN.Therm
sC er
errOr deTeCTed durINg The LearNINg mOde
sp IN
INpuT VOLTage Issue
supp
CONNeCT pOwer COrd TO 240 V sOurCe
upL
The spa paCk dOes NOT haVe VaLId sOFTware. pLease INserT VaLId
IN.sTICk TO reprOgram spa paCk.
TROUBLESHOOTING GUIDE
1
too much water on display
wipe screen
This message appears when too much water is
detected on the touch screen. Simply wipe away
excess water.
installation error messages
Upon connecting the in.k1000 to your spa system you may see one of two error messages.
Please follow the instructions in the message or contact your dealer for more information.
Error messages on-screen list and definitions:
http://geckokeypads.com/k1000errormessages/
9919-101453-C
Rev. 02-2017
www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2017
All trademarks or registered trademarks are the property of their respective owners.
Printed in Canada
1
too much water on display
wipe screen
This message appears when too much water is
detected on the touch screen. Simply wipe away
excess water.
installation error messages
Upon connecting the in.k1000 to your spa system you may see one of two error messages.
Please follow the instructions in the message or contact your dealer for more information.
Error messages on-screen list and definitions:
http://geckokeypads.com/k1000errormessages/
9919-101453-C
Rev. 02-2017
www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2017
All trademarks or registered trademarks are the property of their respective owners.
Printed in Canada