RIKA MultiAir SONO AH, Assembly Instructions Manual

Page: 31 / 48

30
|31
EN
Dimensions of SONO AH
R-
F-
K-
B
H
T
F-H
F-S R-S
R-H
K1-S
K1-H
Dimensions AH
Height [mm] 1050
Width [mm] 690
Corpus depth [mm] 385
Weight
Weight with steel cover [kg] ~150
Weight with stones [kg] ~175
Flue pipe connection
R - Ø Flue pipe outlet [mm] 100
RO - H connection height [cm] -
RO - T1 original angle pipe total depth [cm] -
RO - T2 original angle pipe distance to
rear wall
[cm] -
RO - T3 Depth from rear wall to middle of
flue pipe
[cm] -
RO - S original angle pipe side distance [cm] -
R - H rear connection height [cm] 21
R - S rear connection side distance [cm] 32
Fresh air connection
F - Ø Diameter [mm] 60
F - H Connection height [cm] 8
F - S Side distance [cm] 16
Convection Air Connection
K - Ø Diameter [mm] 100
K - H Connection Height [cm] 55
K - S Side Distance [cm] 18
Amount of Fuel
Nominal
load
Part load
Amount of fuel ~1,6 kg* ~0,6 kg*
Burn time at full pellet hopper ~14h* ~40h*
*Practical values may vary depending on pellet quality.
Note
Pellet consumption depends on the size of the pellets. The larger
the pellets, the slower the feed and vice versa.
(AH) - rear flue pipe connection
Technical data for SONO AH
Technical data
Heating power range [kW]
2,5 - 7
Room heating capacity (depending
on house insulation)
[m3]
50 - 190
Fuel consumption [kg/h]
till 1,6
Pellet container capacity* [l]/[~kg]
39/~25
Electric supply [V]/[Hz]
230/50
Average electrical input [W]
~ 20
Fuse [A]
2,5 AT
Efficiency [%]
92,5
CO
2
[%]
11,3
CO-emission on 13% OO
2
[mg/m
N
3
]
53,5
Dust emission [mg/m
N
3
]
11,5
Exhaust [g/s]
4,8
Exhaust temperature [°C]
142,5
Chimney draft requirement [Pa]
3
*The capacity in kg may deviate due to different pellet bulk
densities.
The owner of small firing systems or the person authorised for the
small firing system is to keep the technical documentation and is to
submit it to the authorities or the chimney sweep on request.
Note
Please observe the national and European standards as well as
local regulations concerning the installation and operation of
firing installations!
Packaging
Your first impression is important to us!
The packaging of your new stove provides excellent protection
against damage. However damage to the stove and accessories
may still occur during transport.
Note
Therefore please check your stove on receipt for damage and
completeness! Report any deficiencies to your dealer immediately!
Pay particular attention during unpacking that the stone panels
remain intact. Scratches to the material can easily occur. Stone
panels are excluded from the warrant.
The packaging of your new stove is environmentally neutral to a
great extent.
Tip
The wood used in the packaging has not been surface treated.
The cardboard and film (PE) can be disposed of via the municipal
waste collection for recycling.
Electrical connection
The stove is supplied with an approx. 2m long connecting cable with
a Euro-plug. This cable is to be connected to a 230Volt/50Hz socket.
The average electrical power consumption is some 20 Watt in
heating operation. And approx. 150 Watt during automatic ignition.
The connection cable must be laid so that there is no contact to any
sharp edges or hot surfaces of the stove.
16. TECHNICAL DATA
ENGLISH