Riello RIELLOtech CLIMA COMFORT Installation, Operation And Maintenance Manual Download Page 5

5

The operation of any appliance that uses electrical power demands that a number of fundamental safety precautions 
be respected. In particular: 

Check that the product is complete and undama-
ged as soon as you remove it from its packaging. 
Contact the 

r

 reseller from whom you purcha-

sed the product if you notice any problems. 

This product must be installed by a legally quali-
fied heating engineer. (In Italy heating engineers 
are regulated by law no. 37 of the 22/01/2008.) On 
completion of the installation, the installer must issue 
the owner with a declaration of conformity confir-
ming that the installation has been completed to the 
highest standards in compliance with the instructions 
provided by 

r

 in this instruction manual, and that 

it conforms to all applicable laws and standards.  

This control panel is designed and made for use with 
boilers generating hot water up to 110°C, and must 
be used exclusively for this purpose and within its 
specified performance limits.  

The manufacturer declines all responsibility, con-
tractual or other, for damage to property or injury to 
persons or animals caused by improper installation, 
adjustment, maintenance or use.  

This instruction manual is an integral part of the 
product. It must be kept safe and must ALWAYS 
accompany the product, even if it is sold to another 
owner or transferred to another user or to another 
installation. If you damage or lose this manual, order 
a replacement immediately from your local 

r

 

Technical Assistance Centre. 

GENERAL SAFETY INFORMATION

PRECAUTIONS

Always turn the 

electrical power supply

 OFF at the 

main switch before commencing any cleaning or 
maintenance.  

Do not tamper with or adjust the safety or control 
devices without prior authorisation and instructions 
from the boiler’s manufacturer. 

Never pull, disconnect, or twist the electrical cables 
coming from the appliance even if it is disconnec-
ted from the mains electricity supply. 

Dispose of packaging materials in compliance with 
applicable standards and legislation governing the 
disposal of urban, domestic and industrial waste. 

Never switch the control panel on even for a short 
period if the safety devices are not functioning cor-
rectly or have been tampered with. 

All maintenance and repairs must be carried out by 
a legally qualified heating engineer. 

Do not use water to extinguish fire in the control 
panel. Switch power OFF at the mains power switch 
to isolate the control panel electrically first. Then 
use a class E fire extinguisher (marked “SUITABLE 
FOR LIVE ELECTRICAL ITEMS”) to extinguish the 
flames. 

Summary of Contents for RIELLOtech CLIMA COMFORT





























































Reviews: