manualshive.com logo in svg

Ricoh K-C3, Service Manual

Share
Download
Ricoh K-C3 Service Manual Download Page 89

B245/B276/B277/B268/B269 Service Manual   

18-Jan-06 

 

80

ƒ

 

Apply toner to the edge of the new cleaning blade when you replace the cleaning 

blade. This prevents possible damage to the OPC drum and blade.

 

1. 

After installing the cleaning blade, remove some of the toner from 

the old blade with your finger.

 

2. 

Apply the toner to the edge [A] of the new cleaning blade. Make 

sure to apply the toner evenly along full length of the new cleaning 

blade.

 

Developer 

 

1. PCU 

(

p.76) 

2.  To let the toner fall to the development section, gently tap about eight different 

spots on the top of the PCU with a screwdriver. Each spot must be approximately 

at an equal distance from the next spot. 

3.  Reinstall the PCU in the copier. 

4.  Turn the main switch on. 

5.  Open and close the front door and wait for the machine to rotate the development 

roller for about 10 seconds. 

6.  Repeat the previous step two more times. 

7. PCU 

(

 p.76) 

8.  Separate the developer section from the OPC drum section (

 p.78). 

9.  Top part [A] of the development unit (  x 5) 

 

Summary of Contents for K-C3


































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands