Ricoh K-C3 Service Manual Download Page 108

Page: 108 / 289

B245/B276/B277/B268/B269 Service Manual

18-Jan-06

NIP Band Width Adjustment

Do this adjustment when the fusing unit is at its operating temperature. The size of the OHP

sheet must be A4/LT LEF. Any other sizes may cause a paper jam.

1. Pressure

roller

2. Hot

roller

1. Place an OHP sheet on the by-pass feed table.

2. Enter SP mode, and run SP 1109.

3. Press ‘1’ (Yes)

4. Press twice. The machine feeds the OHP sheet into the fusing section, stops it

there for 20 seconds, then ejects it to the copy tray.

5. Press

the key.

6. Quit the SP mode.

7. Check that the nip band (the opaque stripe) across the ejected OHP sheet is

symmetrical, with both ends slightly thicker than the center.

There is no standard value for the nip band on this machine. Make the

adjustment based on the band's appearance.

8. If the band is not as described above, change the position of the spring hooks [C]

(one on each side), and then check the band again.

The higher hook position produces greater tension.

Summary of Contents for K-C3


































































































































































































































































































Search results

Summary of Contents for K-C3

Reviews:

Brands by name

Popular brands

Ricoh K-C3, Service Manual

Search results

Summary of Contents for K-C3

Reviews:

Brands by name

Popular brands