manualshive.com logo in svg

Ricoh K-C3, Service Manual

Share
Download
Ricoh K-C3 Service Manual Download Page 252

B245/B276/B277/B268/B269 Service Manual   

18-Jan-06 

 

243

Paper Size Detection 

Paper Tray 

 

SW 

Size 

1 

2 

3 

A3, 11" x 17" 

Off 

Off 

Off 

A4 LEF 

On 

On 

Off 

A4 SEF, 8

1

/

2

" x 11" 

On 

Off 

Off 

A5 LEF, 8

1

/

2

" x 14" 

Off 

On 

On 

8

1

/

2

" x 13" 

On 

Off 

On 

11" x 8

1

/

2

" Off 

On 

Off 

* (Asterisk) 

Off 

Off 

On 

ON=Not pushed, OFF=Pushed 

There are three paper size micro-switches [A] on the front right plate of the paper tray unit. 

The switches are actuated by a paper size actuator [B] behind the paper size indicator plate, 

which is on the front right of the tray. 

Each paper size has its own actuator, with a unique combination of notches. To determine 

which size has been installed, the CPU reads which micro-switches the actuator has 

switched off. 

The CPU disables paper feed from a tray if the paper size cannot be detected. If the paper 

size actuator is broken, or if there is no tray installed, the Add Paper indicator will light. 

When the paper size actuator is at the “*” mark, the paper tray can be set up to accommodate 

one of a wider range of paper sizes by using User Tools. If the paper size for this position is 

changed without changing the User Tool setting, a paper jam will result. 

Summary of Contents for K-C3


































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands