manualshive.com logo in svg

Ricoh FW780, Operating Instructions Manual

Share
Download
Ricoh FW780 Operating Instructions Manual Download Page 13

1

Guide to Components

Copier Exterior

1.

Locks

Squeeze both locks (1a&1b) to open the
unit. Open the unit to empty the used
toner bottle and to remove jammed pa-
per.

2.

Front Cover

Open the cover (and the unit) to access
the toner cartridge.

3.

Original Guides

Use the guides to keep the original
straight as you feed the original into the
copier.

4.

Original Table

Place your original face up here. If you
want to copy a stiff original that can't be
bent, use the rear table (see 6).

5.

Operation Panel

⇒

 P.3 “Operation Panel”.

6.

Rear Table

Place stiff originals face down here.

7.

Roll Feeder

Feeds paper from a roll to the copier.

8.

Paper Guides

Use the guides to keep the copy paper
straight as you feed it into the copier.

9.

Bypass Table

Use this table when you want to make
copy one by one.

10.

Table

Holds your copier and the Roll Feeder.

Summary of Contents for FW780


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands