manualshive.com logo in svg

Ricoh FW780, Operating Instructions Manual

The Ricoh FW780 Operating Instructions Manual is a comprehensive guide that equips users with the necessary knowledge to operate the Ricoh FW780 product seamlessly. This detailed manual is available for free download from our website, providing users easy access to essential information on optimizing their product usage.

Share
Download
background image

vi

TABLE OF CONTENTS

Guide to Components ...............................................................................  1

Copier Exterior ..............................................................................................  1
Operation Panel ............................................................................................  3

1. Basics

Turning on the Power................................................................................  5

Turn on the Main Power ................................................................................  5
Turn off the Main Power ................................................................................  5

Recommended Originals ..........................................................................  6

Non-recommended Originals ........................................................................  7
Note for Leading and Side Edges of the Originals ........................................  7

Recommended Paper................................................................................  8

Anti-humidity Heater......................................................................................  9

Toner.........................................................................................................  10

Handling Toner............................................................................................  10
Toner Storage .............................................................................................  10
Used Toner .................................................................................................  10

2. Copying

Basic Copying (Copying to sheets) .......................................................  11

Manual Feed Mode .....................................................................................  16
Using the Rear Table ..................................................................................  19

Copying onto Roll Paper.........................................................................  21

Synchro Cutting...........................................................................................  21
Preset Cutting .............................................................................................  24
Variable Cutting...........................................................................................  25

3. Copy Settings

Copying onto Other Media......................................................................  27

Adjusting the Fusing Temperature Manually...............................................  28

Adjusting Copy Image Density...............................................................  30

Setting the Number of Copies (Repeated Copying) .............................  31

Setting a Leading/Trailing Edge Margin ................................................  32

Partial Copying ........................................................................................  34

Programming Settings You Often Use ..................................................  37

A) Program key ...........................................................................................  37
B) Changing the Default Setting..................................................................  38

User Tools ................................................................................................  40

Settings You Can Change with User Tools...........................................  42

Summary of Contents for FW780


































































































Reviews:

No comments

Related manuals for FW780

Telecrane F25 Installation & Operation Manual preview
F25
Brand: Telecrane Pages: 32
Minolta EP3050 Operator'S Manual preview
EP3050
Brand: Minolta Pages: 206

Brands by name

Popular brands

Load more brands