Ricoh AP610N - Aficio B/W Laser Printer Maintenance Manual Download Page 89 | Manualshive

Page: 89 / 124

background image

Troubleshooting

89

Other Printing Problems

Status

Possible Causes, Descriptions, and Solutions

The print side of the page
is a hazy gray.

Adjust the image density.

p.70 “Adjusting the Image Density”

If paper is curled, correct it.

If you continuously print data that contains extremely small amount
of words or images in the printable area, the printed side of the
page could be a hazy gray. Adjust the image density.

p.70 “Adjusting the Image Density”

Shaking the toner cartridge after pulling out the toner seal can
cause dirt on paper surfaces, toner spillage, or printer failure. If you
have accidentally shaken the toner cartridge, print some pages
(about 50 pages) until the dirt disappear.

The paper's reverse side
is dirty.

Paper loaded in the Paper Tray or paper feed unit may not match
the paper size dial setting. Set the paper size dial so it matches the
size and feed direction of the paper in the tray.

p.16 “Loading Paper in Tray 1 and the optional paper feed

.

The size and feed direction of paper in the Bypass Tray may not
match the control panel settings. Check the control panel settings
so they match the size and feed direction of the paper in the tray.

p.26 “Loading Paper in the Bypass Tray”

The next sheet of paper printed may have a dirtied reverse side if
the data size is larger than the paper being printed onto, such as
A4 data onto B5 paper.

Image quality varies when
printing on thick paper or
on OHP transparencies.

Switch to Thick Paper mode.

•

When toner is not fused enough, set it to “On”.

•

When the image is blurred, set it to “----”.

See “Making Printer Setting Using Control panel”, Software Guide.

Some parts of the print im-
age are not clear.

Make the image density darker.

p.70 “Adjusting the Image Density”

If Toner Saving mode is selected using the control panel, the whole
image gets lighter.

The print image is not
clear.

Due to a sudden change in temperature, condensation might ap-
pear inside the printer, reducing print quality. If this occurs, when
you move the printer from a cold room to a warmer room, do not
use the printer until it acclimatizes to the temperature.

«
...
87
88
89
90
91
...
»

Summary of Contents for AP610N - Aficio B/W Laser Printer





























































































































Reviews:

No comments

Related manuals for AP610N - Aficio B/W Laser Printer

Brand: Qls Pages: 53

Brand: Xerox Pages: 36

Brand: IBM Pages: 16

Brand: Xerox Pages: 23

Brand: IBM Pages: 113

Brand: IBM Pages: 16

Brand: IBM Pages: 214

Brand: NCR Pages: 224

SelfServ Checkout 7350

Brand: NCR Pages: 20

Brand: Qilive Pages: 398

Brand: Z Corporation Pages: 76

Brand: Xerox Pages: 44

Brand: Printronix Pages: 9

Aficio SP C730DN

Brand: Ricoh Pages: 100

MINI THERMAL RP-3180

Brand: TVS electronics Pages: 19

VarioLink 2650cp

Brand: Oce Pages: 2

SpeedSetter 300

Brand: Xante Pages: 1

Brand: SPRT Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands